46 open source boards using the Opamp_Dual

Real designs built with the Opamp_Dual, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

46 boardsClear filters|Most starred

How designs wire the Opamp_Dual

Read from the KiCad layouts of 25 open source designs, one per repository: what each pin of the Opamp_Dual connects to, and the resistors, capacitors and other passives placed on it.

  • Pin 1 has a series resistor on 21 of 25 designs, most often 10 kΩ (then 100 kΩ).
  • The - pins have a series resistor on 18 of 25 designs, most often 100 kΩ (then 10 kΩ).
  • The + pins have a series resistor on 16 of 25 designs, most often 10 kΩ (then 1 kΩ).
  • Pin 7 has a series resistor on 16 of 25 designs, most often 0 Ω (then 10 kΩ).
Pin 1Connected to: Signal 92%
  • Series resistor on 84% · 10 kΩ (7), 100 kΩ (3), 470 Ω (3)
-pin 2, 6Connected to: Signal 84%
  • Series resistor on 72% · 100 kΩ (11), 10 kΩ (9), 1 kΩ (4)
+pin 3, 5Connected to: Signal 80%
  • Series resistor on 64% · 10 kΩ (12), 1 kΩ (4), 100 kΩ (3)
  • Resistor to GND on 60% · 1 kΩ (4), 10 kΩ (3), 166 kΩ (2)
V-pin 4Connected to: GND 68% · -12V 20%
Pin 7Connected to: Signal 88%
  • Series resistor on 64% · 0 Ω (4), 10 kΩ (4), 1 kΩ (3)
V+pin 8Connected to: 5V 84% · a signal 16%
  • Decoupling capacitor on 56% · 100 nF (12), 1 µF (3), 10 µF (2)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Mixer by QuinnFreedman, Ultimate soldering exercise by dvhx, ECE342 USB Oscilliscope by elliotnash and Design files CB by bu-gsLab.

The Opamp_Dual in open source designs

The gallery holds 46 open source boards using the Opamp_Dual from 26 GitHub repositories; a typical one measures about 80.3 × 65.5 mm and carries around 71 components.

80% are two-layer designs, the rest use four layers or more, and 30% carry an open source license.

The most starred is Mixer by QuinnFreedman.

Parts used alongside the Opamp_Dual

Microcontrollers on boards using the Opamp_Dual

Opamp_Dual: common questions

Where can I find a Opamp_Dual reference design?

Each of the 46 boards on this page is a real design using the Opamp_Dual. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the Opamp_Dual pin 1?

Pin 1 has a series resistor on 21 of 25 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 25 open source designs using the Opamp_Dual.

What resistor goes on the Opamp_Dual - pin?

The - pins have a series resistor on 18 of 25 designs, most often 100 kΩ (then 10 kΩ). Counted from the KiCad layouts of 25 open source designs using the Opamp_Dual.

What resistor goes on the Opamp_Dual + pin?

The + pins have a series resistor on 16 of 25 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 25 open source designs using the Opamp_Dual.

What parts are used alongside the Opamp_Dual?

The LM13700, Opamp_Quad, TL072 and W25Q128JVS appear in the most repositories here.

Which microcontrollers do boards using the Opamp_Dual use?

Most are built on AVR/Arduino (5), RP2040/RP2350 (4), PIC (2) and ESP32 (1).

How big is a typical board using the Opamp_Dual?

The median is 80.3 × 65.5 mm, and 80% are two-layer designs.

What is the most popular open source board using the Opamp_Dual?

By GitHub stars, Mixer by QuinnFreedman, with 114 stars.

Can I simulate one of these boards using the Opamp_Dual before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part