Usbc esp32-pump controller
CarloMara·usbc-esp32-pump-controller
About the Usbc esp32-pump controller PCB
Usbc esp32-pump controller is an open source ESP32 PCB design by CarloMara, published on GitHub. It is a 2-layer board measuring 65 × 47.4 mm, with 60 components from 19 distinct parts.
Its main chip is the ESP32-S3-MINI-1, from the ESP32 family. Other key parts include the CYPD3177-24LQ. By type, the board carries 23 resistors, 11 capacitors, 8 transistors, 8 connectors, 7 diodes and 2 ICs.
It belongs with the power & battery designs in this gallery.
From the project
USB C PD pump controller for small plants
Main components on the Usbc esp32-pump controller
Usbc esp32-pump controller bill of materials (BOM)
60 components, 19 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CYPD3177-24LQ | QFN-24-1EP_4x4mm_P0.5mm_EP2.75x2.75mm | U1 |
| 1 | ESP32-S3-MINI-1 | ESP32-S2-MINI-1 | U2 |
| 2 | DMP3013SFV | Diodes_PowerDI3333-8 | Q1, Q2 |
| 6 | AO3400A | SOT-23 | Q3, Q4, Q5, Q6, Q7, Q8 |
| 1 | USB_C_Receptacle | USB_C_Receptacle_GCT_USB4110 | J1 |
| 1 | Screw_Terminal_01x02 | PinHeader_1x02_P2.00mm_Vertical | J2 |
| 6 | MOTOR | PinHeader_1x02_P2.00mm_Vertical | J3, J5, J6, J7, J8, J9 |
| 1 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | SW1 |
| 1 | 15V | D_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 6 | SS34 | D_SMA | D2, D3, D4, D5, D6, D7 |
| 1 | 3.3uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 4 | 1uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3, C6, C7 |
| 4 | 0.1uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C5, C8, C11 |
| 2 | 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9, C10 |
| 5 | 10K | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2, R13, R14, R15, R22 |
| 1 | 47k | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3 |
| 9 | 1k | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R4, R5, R6, R7, R8, R9, R10, R11 +1 |
| 6 | 100 | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R16, R17, R18, R19, R20, R21 |
| 2 | 22 | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R23, R24 |
Usbc esp32-pump controller design files
The KiCad project lives in the CarloMara/usbc-esp32-pump-controller repository on GitHub; these links point at the commit this page was built from.
Usbc esp32-pump controller: common questions
What microcontroller does the Usbc esp32-pump controller use?
The Usbc esp32-pump controller is built around the ESP32-S3-MINI-1, from the ESP32 family.
How big is the Usbc esp32-pump controller PCB?
The Usbc esp32-pump controller measures 65 × 47.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Usbc esp32-pump controller?
60 components, from 19 distinct parts. The full bill of materials is listed on this page.
Where can I download the Usbc esp32-pump controller design files?
From the CarloMara/usbc-esp32-pump-controller repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Usbc esp32-pump controller design in my own project?
The repository has no license, so all rights stay with CarloMara. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Usbc esp32-pump controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k