11 open source boards using the CYPD3177-24LQ
Real designs built with the CYPD3177-24LQ, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
FabRice
dev-campusfab
70 × 43.5 mm52 parts2LMIT4RP2040/RP2350
Raspberry pi power hub
tobycm
39 × 27 mm65 parts2LMIT2TorxHAT
RobotStudyCompanion
65 × 56.6 mm78 parts2LCustom license1ESP32
Lamp-2
DodoZimmermann
147 × 139.9 mm248 parts6LMIT0ESP32
Prototyp
Huruvarshan
160 × 100 mm98 parts4LMIT0ESP32
Usbc esp32-pump controller
CarloMara
65 × 47.4 mm60 parts2LNo license0Pd test board
Phaeilo
53.2 × 45.8 mm49 parts4LCERN-OHL-P-2.00Usb c pd bcr quickie
asm2750
50.8 × 19.1 mm37 parts2LCERN-OHL-W-2.00- schematic only · 58 partsESP32
Esp32 PD
Joshm196
58 partsNo license0 Power Delivery
Network-Direction
69.9 × 32.8 mm31 parts2LNo license0USB-C-PD-Controller
Rowan-Rocketry
53.3 × 24.9 mm36 parts2LNo license1
How designs wire the CYPD3177-24LQ
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the CYPD3177-24LQ connects to, and the resistors, capacitors and other passives placed on it.
- The VCCD pin has a capacitor to GND on 10 of 10 designs, most often 1 µF (then 4.7 µF).
- The ISNK_COARSE pin has a resistor to GND on 9 of 10 designs, most often 2.4 kΩ (then 5.1 kΩ).
- The ISNK_COARSE pin has a pull-up to 3.3V on 9 of 10 designs, most often 5.1 kΩ (then 2.2 kΩ).
- The VDDD pin has a decoupling capacitor on 9 of 10 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VBUS_MAXpin 2 | Connected to: Signal 60% · VBUS_MAX 40% |
|
| VBUS_FET_ENpin 3 | Connected to: Signal 70% · VBUS_FET_EN 30% |
|
| SAFE_PWR_ENpin 4 | Connected to: Not connected 60% · a signal 40% | — |
| ISNK_COARSEpin 5 | Connected to: Signal 100% |
|
| ISNK_FINEpin 6 | Connected to: GND 50% · a signal 50% |
|
| GPIO_1pin 8 | Connected to: Not connected 80% · a signal 20% | — |
| FLIPpin 10 | Connected to: Signal 100% |
|
| VDC_OUTpin 11 | Connected to: VBUS 60% · a signal 40% | — |
| HPI_SDApin 12 | Connected to: The microcontroller 30%, a connector 20% · not connected 20% |
|
| HPI_SCLpin 13 | Connected to: The microcontroller 30%, a connector 20% · not connected 20% |
|
| NCpin 16, 17, 20, 21 | Connected to: Not connected 100% | — |
| VBUS_INpin 18 | Connected to: A connector 40% · VBUS 40% |
|
| GNDpin 19, 22, 25 | Connected to: GND 100% | — |
| VDDDpin 23 | Connected to: 3.3V 90% |
|
| VCCDpin 24 | Connected to: Signal 80% · 1.8V 20% |
|
5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include FabRice by dev-campusfab, Raspberry pi power hub by tobycm, TorxHAT by RobotStudyCompanion and USB-C-PD-Controller by Rowan-Rocketry.
The CYPD3177-24LQ in open source designs
The gallery holds 11 open source boards using the CYPD3177-24LQ from 11 GitHub repositories; a typical one measures about 65 × 44.6 mm and carries around 58 components.
70% are two-layer designs, the rest use four layers or more, and 55% carry an open source license.
The most starred is FabRice by dev-campusfab.
Parts used alongside the CYPD3177-24LQ
Microcontrollers on boards using the CYPD3177-24LQ
What boards using the CYPD3177-24LQ are built for
CYPD3177-24LQ: common questions
Where can I find a CYPD3177-24LQ reference design?
Each of the 11 boards on this page is a real design using the CYPD3177-24LQ. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the CYPD3177-24LQ VCCD pin connected?
The VCCD pin has a capacitor to GND on 10 of 10 designs, most often 1 µF (then 4.7 µF). Counted from the KiCad layouts of 10 open source designs using the CYPD3177-24LQ.
What resistor goes on the CYPD3177-24LQ ISNK_COARSE pin?
The ISNK_COARSE pin has a resistor to GND on 9 of 10 designs, most often 2.4 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 10 open source designs using the CYPD3177-24LQ.
What decoupling capacitors do designs use on the CYPD3177-24LQ VDDD pin?
The VDDD pin has a decoupling capacitor on 9 of 10 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 10 open source designs using the CYPD3177-24LQ.
Which microcontrollers do boards using the CYPD3177-24LQ use?
Most are built on ESP32 (5) and RP2040/RP2350 (1).
How big is a typical board using the CYPD3177-24LQ?
The median is 65 × 44.6 mm, and 70% are two-layer designs.
What is the most popular open source board using the CYPD3177-24LQ?
By GitHub stars, FabRice by dev-campusfab, with 4 stars.
Can I simulate one of these boards using the CYPD3177-24LQ before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.