HardLabs

IMX6ULL tryout

cebrax·iMX6ULL_tryout·imx6ull_tryout/imx6ull_tryout.kicad_pcb

IMX6ULL tryout PCB layout, top view — open source Microchip SAM board by cebrax

About the IMX6ULL tryout PCB

IMX6ULL tryout is an open source Microchip SAM PCB design by cebrax, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 100 × 75 mm, with 171 components from 48 distinct parts.

Its main chip is the ATSAMD10D13, from the Microchip SAM family. Other key parts include the iMX6ULL, F60C1A0004-M79R, DP83825, TPS61169 and 78L05. By type, the board carries 80 capacitors, 45 resistors, 14 test points, 12 connectors, 8 ICs and 3 diodes.

It belongs with the dev boards & breakouts designs in this gallery.

From the project

iMX6ULL development board

This is a test board to get iMX6ULL up and running using KiCad 5.99

- iMX6ULL 900MHz MCIMX6Y2DVM09AB - 512MB DDR3L RAM - An SD card slot - 2 x USB connector - An ethernet PHY and connector with magnetics - A 40-pin LCD connector - Various pinouts of GPIO, RS232 and such..

IMX6ULL tryout, from the project README
From the project README

Main components on the IMX6ULL tryout

iMX6ULLF60C1A0004-M79RDP83825TPS6116978L05TPS56x200ATSAMD10D13

IMX6ULL tryout bill of materials (BOM)

171 components, 48 distinct parts.

QtyPartRefs
1
iMX6ULL
U1
1
F60C1A0004-M79R
U2
1
DP83825
U4
1
TPS61169
U5
1
78L05
U6
2
TPS56x200
U7, U8
1
ATSAMD10D13
U9
1
X1E0000210065
X1
1
FC-135 32.7680KA-E3
X2
1
47352-1001
P1
1
Connector-RJ45-J1B1211CCD
P2
1
LCD-40
P3
2
DS1095-WNR0
P4, P5
1
POWER IN
P6
1
UART1
P7
1
UART3
P8
1
I2S
P9
1
ECSPI4
P10
1
GPIO2
P11
1
SWD Programmer
P12
Show 28 more
QtyPartRefs
4
SCREW
MS1, MS2, MS3, MS4
14
TEST_POINT
TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 +6
1
BAT54T1G
D1
1
ES1D
D2
1
LED
D3
2
10uH
L1, L3
1
4.7uH
L2
45
1uF
C1, C2, C7, C8, C9, C10, C11, C12 +37
2
1uF
C3, C5
7
22uF
C4, C35, C39, C40, C51, C65, C69
6
10uF
C6, C41, C44, C46, C59, C70
6
10uF
C15, C71, C74, C76, C78, C80
5
18pF
C47, C48, C49, C50, C62
5
100nF
C63, C64, C73, C75, C79
1
10uF
C67
3
220uF
C72, C77, C81
17
240R
R1, R8, R32, R33, R34, R35, R36, R37 +9
11
10k
R2, R3, R4, R9, R10, R11, R25, R27 +3
1
470R
R5
4
1k5
R6, R7, R24, R47
2
10k
R12, R13
2
10R
R16, R22
2
1k
R17, R18
1
6k49
R19
2
2k49
R20, R21
1
10R
R23
1
33k2
R26
1
7k68
R29

IMX6ULL tryout design files

The KiCad project lives in the cebrax/iMX6ULL_tryout repository on GitHub; these links point at the commit this page was built from.

IMX6ULL tryout: common questions

What microcontroller does the IMX6ULL tryout use?

The IMX6ULL tryout is built around the ATSAMD10D13, from the Microchip SAM family.

How big is the IMX6ULL tryout PCB?

The IMX6ULL tryout measures 100 × 75 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the IMX6ULL tryout?

171 components, from 48 distinct parts. The full bill of materials is listed on this page.

Where can I download the IMX6ULL tryout design files?

From the cebrax/iMX6ULL_tryout repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the IMX6ULL tryout design in my own project?

Yes, under the terms of its GPL-3.0 license, which cebrax chose for the repository.

Can I test firmware for the IMX6ULL tryout without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.

Similar boards