Half-Life-Hack-Club

Chicken-Nugget-N·Half-Life-Hack-Club·First-Kicad/First-Kicad.kicad_pcb

Half-Life-Hack-Club PCB layout, top view — open source ESP32 board by Chicken-Nugget-N

About the Half-Life-Hack-Club PCB

Half-Life-Hack-Club is an open source ESP32 PCB design by Chicken-Nugget-N, published on GitHub. It is a 2-layer board measuring 163.2 × 155.2 mm, with 12 components from 11 distinct parts.

Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 3 connectors, 2 ICs, 2 switches, 2 resistors, 1 buzzer and 1 diode.

It belongs with the sensors and iot & wireless designs in this gallery.

From the project

Week 1: Starbie Starter Project Made the starbie starter project because I don't have much experience with PCB CAD. Modified my starbie with Ultrasonic Sensor, LED, Potentiometer, and buzzer. Not sure how to implement them yet.

Week 1: Starbie Starter Project Made the starbie starter project because I don't have much experience with PCB CAD. Modified my starbie with Ultrasonic Sensor, LED, Potentiometer, and buzzer. Not sure how to implement them yet.

I decided to make this starbie because I needed an intro to pcb design during the Half life hack club. I'm really excited to do this project because I want to gain more experience with hardware and electronics. I started by following instructions on importing all the necessary footprints and schematics in KiCad, and then designed a schematic with sections for a…

Half-Life-Hack-Club, from the project README
From the project README

Main components on the Half-Life-Hack-Club

Half-Life-Hack-Club bill of materials (BOM)

12 components, 11 distinct parts.

QtyPartRefs
1
DHT11
U1
1
XIAO-ESP32-C3-SMD
U2
1
Conn_01x04_Pin
J1
1
Conn_01x08_Pin
J2
1
Conn_01x04_Pin
J3
1
Buzzer
BZ1
1
R_Potentiometer
RV1
2
SW_Push
SW1, SW2
1
LED
D1
1
10k
R1
1
330
R2

Half-Life-Hack-Club design files

The KiCad project lives in the Chicken-Nugget-N/Half-Life-Hack-Club repository on GitHub; these links point at the commit this page was built from.

Half-Life-Hack-Club: common questions

What microcontroller does the Half-Life-Hack-Club use?

The Half-Life-Hack-Club is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.

How big is the Half-Life-Hack-Club PCB?

The Half-Life-Hack-Club measures 163.2 × 155.2 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Half-Life-Hack-Club?

12 components, from 11 distinct parts. The full bill of materials is listed on this page.

Where can I download the Half-Life-Hack-Club design files?

From the Chicken-Nugget-N/Half-Life-Hack-Club repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Half-Life-Hack-Club design in my own project?

The repository has no license, so all rights stay with Chicken-Nugget-N. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Half-Life-Hack-Club without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards