USB-WLED-Controller
Choccy-vr·WLED-Controller·PCB/USB/USB-WLED-Controller.kicad_pcb
About the USB-WLED-Controller PCB
USB-WLED-Controller is an open source ESP32 PCB design by Choccy-vr, published on GitHub. It is a 4-layer board measuring 18.3 × 42.3 mm, with 39 components from 24 distinct parts.
Its main chip is the ESP32-C3, from the ESP32 family. Other key parts include the AMS1117-3.3 and SN74LVC4245APWR. By type, the board carries 18 capacitors, 9 resistors, 3 ICs, 2 switches, 1 transistor and 1 crystal.
It belongs with the displays & leds designs in this gallery.
From the project
A all in one controller for ws2812b led strips made for WLED
I made this because these WS2812B strips and WLED look so good, but all the other WLED controllers are quite expensive, and I would rather make it by myself. I set out to make it as small as possible, even if that means making it harder for me.
On the controller PCB, I integrated basically a esp32 c3 supermini. That is the bulk of it, but I also put some capacitors on the LED PWR line for smoothing the power out. I also added a P-channel MOSFET to allow for a soft start.

Main components on the USB-WLED-Controller
USB-WLED-Controller bill of materials (BOM)
39 components, 24 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | SN74LVC4245APWR | SOP65P640X120-24N | U2 |
| 1 | ESP32-C3 | QFN-32_L5.0-W5.0-P0.50-TL-EP3.7 | U3 |
| 1 | SI2319CDS Si2319CDS | SOT-23 | Q1 |
| 1 | CRYSTAL_GND24 Crystal_GND24 | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | LED Connector | PinSocket_1x03_P2.54mm_Vertical | J2 |
| 1 | ANT3216A063R2400A | XDCR_ANT3216A063R2400A | E1 |
| 1 | C720477 BOOT | SW_SPST_TS-1088-xR020 | SW1 |
| 1 | C720477 RST | SW_SPST_TS-1088-xR020 | SW2 |
| 1 | C2765186 TYPE-C 16PIN 2MD(073) | USB-C-SMD_TYPE-C-6PIN-2MD-073 | USB1 |
| 1 | SS14 | D_SMA | D1 |
| 1 | 2.7NH 2.7nH | L_0402_1005Metric | L1 |
| 3 | 10UF 10uf | C_0402_1005Metric | C1, C15, C16 |
| 5 | 1UF 1uf | C_0402_1005Metric | C2, C4, C7, C8, C17 |
| 4 | 100NF 100nf | C_0402_1005Metric | C3, C5, C6, C14 |
| 1 | 10NF 10nf | C_0402_1005Metric | C9 |
| 2 | 15PF 15pf | C_0402_1005Metric | C10, C11 |
| 2 | 1.5PF 1.5pf | C_0402_1005Metric | C12, C13 |
| 1 | 470UF 470uf | CP_Radial_D10.0mm_P5.00mm | C18 |
| 3 | 10K 10k | R_0402_1005Metric | R1, R2, R3 |
Show 4 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 5.1K 5.1k | R_0402_1005Metric | R4, R5 |
| 2 | 22OHM 22Ohm | R_0402_1005Metric | R6, R7 |
| 1 | 220 | R_0402_1005Metric | R8 |
| 1 | 100K 100k | R_0402_1005Metric | R9 |
USB-WLED-Controller design files
The KiCad project lives in the Choccy-vr/WLED-Controller repository on GitHub; these links point at the commit this page was built from.
USB-WLED-Controller: common questions
What microcontroller does the USB-WLED-Controller use?
The USB-WLED-Controller is built around the ESP32-C3, from the ESP32 family.
How big is the USB-WLED-Controller PCB?
The USB-WLED-Controller measures 18.3 × 42.3 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the USB-WLED-Controller?
39 components, from 24 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the USB-WLED-Controller design files?
From the Choccy-vr/WLED-Controller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the USB-WLED-Controller design in my own project?
The repository has no license, so all rights stay with Choccy-vr. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the USB-WLED-Controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k