Esp32-s3-dev board
chof747·esp32-s3-dev-board
About the Esp32-s3-dev board
Esp32-s3-dev board is an open source ESP32 PCB design by chof747, published on GitHub under the CC0-1.0 license. It is a 2-layer board measuring 30.8 × 50 mm, with 14 components from 13 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8R8, from the ESP32 family. By type, the board carries 3 connectors, 2 switches, 2 capacitors, 2 resistors, 1 IC and 1 transistor.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
ESP32-S3 development board with minimal additional components
- ESP32 MCU with all available pins broken out - Programming header with DTR/RTS mechanism - Power LED - Fuse to prevent the worse - Jumper to disconnect 3v3 from the programmer to be able to test e.g. battery mode while still debugging
- v1.0: Initial version (filed for fabrication: 19.11.2022, first successfull assembly: 29.11.2022) - v1.1: Changed serial programmer to UMH3 chip and added boot button
Main components on the Esp32-s3-dev board
Esp32-s3-dev board bill of materials (BOM)
14 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N8R8 | ESP32S3WROOM1N8R8 | IC1 |
| 1 | UMH3N | SOT-363_SC-70-6 | Q1 |
| 2 | Conn_01x18 | PinHeader_1x18_P2.54mm_Vertical | J1, J2 |
| 1 | PROG_HDR | PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | Fuse | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | PWR_PROG | PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | Reset | SW_PUSH_6mm | SW1 |
| 1 | Boot | SW_PUSH_6mm | SW2 |
| 1 | PWR | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | 10uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1 |
| 1 | 1uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2 |
| 1 | 22k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
Esp32-s3-dev board design files
The KiCad project lives in the chof747/esp32-s3-dev-board repository on GitHub; these links point at the commit this page was built from.
- Layoutesp32-s3-dev-board.kicad_pcb
- Schematicesp32-s3-dev-board.kicad_sch
Esp32-s3-dev board: common questions
What microcontroller does the Esp32-s3-dev board use?
The Esp32-s3-dev board is built around the ESP32-S3-WROOM-1-N8R8, from the ESP32 family.
How big is the Esp32-s3-dev board?
The Esp32-s3-dev board measures 30.8 × 50 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-s3-dev board?
14 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp32-s3-dev board design files?
From the chof747/esp32-s3-dev-board repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp32-s3-dev board design in my own project?
Yes, under the terms of its CC0-1.0 license, which chof747 chose for the repository.
Can I test firmware for the Esp32-s3-dev board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k