Protoboard
clintval·esphome-kaidi-desk·hardware/proto/protoboard.kicad_pcb
About the Protoboard PCB
Protoboard is an open source ESP32 PCB design by clintval, published on GitHub under the MIT license. It is a 2-layer board measuring 50.8 × 38.1 mm, with 21 components from 20 distinct parts.
Its main chip is the ESP32-C3_SuperMini_LabelsUp, from the ESP32 family. Other key parts include the 74AHCT125. By type, the board carries 7 resistors, 2 ICs and 1 capacitor.
It belongs with the iot & wireless designs in this gallery.
From the project
Control a Kaidi standing desk from Home Assistant with an ESP32 and ESPHome
Control a Kaidi standing desk from Home Assistant with an ESP32 and ESPHome.
Many "K Series" and other budget standing desks run on a Kaidi control box, such as the KDDY094. The box talks to its keypad over a 9600 baud serial link on a 10-pin RJ50 cable, and no off-the-shelf smart-desk dongle speaks its protocol. This component reads the desk's height and drives it the way the keypad does: it raises the keypad's wake line to power the motors, waits for the box to settle, then streams Up, Down and Reset commands. Earlier Kaidi projects only listened to the box; moving the desk needed the wake…

Main components on the Protoboard
Protoboard bill of materials (BOM)
21 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3_SuperMini_LabelsUp | ESP32-C3_SuperMini_LabelsUp | U1 |
| 1 | 74AHCT125 | DIP-14_W7.62mm | U2 |
| 1 | EPLZON_Mini_17x10 | EPLZON_Mini_17x10 | B1 |
| 1 | Wire_A2_A13 | Wire_A2_A13 | W1 |
| 1 | Wire_B3_B11 | Wire_B3_B11 | W2 |
| 1 | Wire_D10_D15 | Wire_D10_D15 | W3 |
| 1 | Wire_J8_J11 | Wire_J8_J11 | W4 |
| 1 | Wire_G13_G14 | Wire_G13_G14 | W5 |
| 1 | Wire_H10_H12 | Wire_H10_H12 | W6 |
| 1 | Wire_I12_I15 | Wire_I12_I15 | W7 |
| 1 | Wire_D16_F17 | Wire_D16_F17 | W8 |
| 1 | Wire_C14_G15 | Wire_C14_G15 | W9 |
| 1 | Wire_H2_G17 | Wire_H2_G17 | W10 |
| 1 | 100nF | C_Disc_P5.08 | C1 |
| 1 | 1k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_Vertical | R2 |
| 1 | 100k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 |
| 2 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4, R7 |
| 1 | 100k | R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R5 |
| 1 | 4.7k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R6 |
Protoboard design files
The KiCad project lives in the clintval/esphome-kaidi-desk repository on GitHub; these links point at the commit this page was built from.
Protoboard: common questions
What microcontroller does the Protoboard use?
The Protoboard is built around the ESP32-C3_SuperMini_LabelsUp, from the ESP32 family.
How big is the Protoboard PCB?
The Protoboard measures 50.8 × 38.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Protoboard?
21 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the Protoboard design files?
From the clintval/esphome-kaidi-desk repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Protoboard design in my own project?
Yes, under the terms of its MIT license, which clintval chose for the repository.
Can I test firmware for the Protoboard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in esphome-kaidi-desk
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k