HardLabs

LED remote

CodedSakura·electronics·LED driver/LED remote.kicad_pcb

LED remote PCB layout, top view — open source ESP32 board by CodedSakura

About the LED remote PCB

LED remote is an open source ESP32 PCB design by CodedSakura, published on GitHub. It is a 2-layer board measuring 30 × 100 mm, with 55 components from 35 distinct parts.

Its main chip is the ESP32-C3-MINI-1-N4, from the ESP32 family. Other key parts include the TPS63001, MCP73833-AMI/UN, MC74HC165ADG and ADXL345BCCZ. By type, the board carries 21 resistors, 12 capacitors, 10 switches, 5 ICs, 2 connectors and 1 battery holder.

Main components on the LED remote

TPS63001MCP73833-AMI/UNESP32-C3-MINI-1-N4MC74HC165ADGADXL345BCCZ

LED remote bill of materials (BOM)

55 components, 35 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TPS63001
U1
1
MCP73833-AMI/UN
U2
1
ESP32-C3-MINI-1-N4
U3
1
MC74HC165ADG
U4
1
ADXL345BCCZ
U5
1
USB4105-GF-A
J1
1
Conn_UART
J2
1
Li-Po
BT1
1
Boot_Mode
JP2
1
JS102000SAQN
SW1
1
SW_Push
SW2
1
ON/OFF
SW3
1
MENU
SW4
1
LEFT
SW5
1
UP
SW6
1
OK
SW7
1
DOWN
SW8
1
BACK
SW9
1
RIGHT
SW10
1
OLED-128O064D
DS1
Show 15 more
QtyPartRefs
1
MP001251
D1
1
LPS4012-222MRC
L1
5
10uF
C1, C3, C4, C8, C10
3
0.1uF
C2, C7, C9
2
1uF
C5, C6
2
4.7uF
C11, C12
3
100
R1, R2, R3
1
150
R4
1
1K
R5
6
10K
R6, R9, R10, R11, R17, R19
2
5.1K
R7, R8
3
4.7K
R12, R13, R14
1
24K
R15
2
LDR
R16, R18
2
YC248-JR-074K7L
RN1, RN2

LED remote design files

The KiCad project lives in the CodedSakura/electronics repository on GitHub; these links point at the commit this page was built from.

LED remote: common questions

What microcontroller does the LED remote use?

The LED remote is built around the ESP32-C3-MINI-1-N4, from the ESP32 family.

How big is the LED remote PCB?

The LED remote measures 30 × 100 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the LED remote?

55 components, from 35 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the LED remote design files?

From the CodedSakura/electronics repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the LED remote design in my own project?

The repository has no license, so all rights stay with CodedSakura. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the LED remote without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in electronics

Similar boards