HardLabs

Prime Mover

dannyandreev·TheLittleRascal-Electrical·Prime Mover V1.4/Prime Mover.kicad_pcb

Prime Mover PCB layout, top view — open source Raspberry Pi board by dannyandreev

About the Prime Mover PCB

Prime Mover is an open source Raspberry Pi PCB design by dannyandreev, published on GitHub under the MIT license. It is a 2-layer board measuring 80.1 × 56 mm, with 37 components from 24 distinct parts.

Its main chip is the Raspberry_Pi_2_3, from the Raspberry Pi family. Other key parts include the NTS0308EPWJ, MAX20404AFOC/VY+, PCA9685 and MCP3008. By type, the board carries 12 connectors, 10 capacitors, 7 resistors, 5 ICs, 1 jumper and 1 diode.

Main components on the Prime Mover

NTS0308EPWJMAX20404AFOC/VY+PCA9685MCP3008

Prime Mover bill of materials (BOM)

37 components, 24 distinct parts.

QtyPartRefs
1
NTS0308EPWJ
IC1
1
MAX20404AFOC/VY+
MAX20404AFOC_VY+
IC2
1
PCA9685
U1
2
MCP3008
U2, U3
3
Conn_01x06_Male
J1, J6, J7
1
Conn_01x04_Male
J2
2
Conn_01x03_Male
J3, J5
1
Conn_01x09_Male
J4
3
Conn_01x07_Male
J8, J9, J10
1
Conn_01x02_Male
J11
1
Conn_01x08_Male
J12
1
Jumper_2_Bridged
JP1
1
3V6
D1
1
MWSA0605S-150MT
1uH
L1
2
0.1uF
C1, C2
1
2.2uF
C3
3
22uF
C4, C6, C8
2
4.7uF
C5, C7
2
1.0uF
C9, C10
2
4k7
R1, R2
Show 4 more
QtyPartRefs
1
Raspberry_Pi_2_3
R3
1
4.7k
R4
1
1.5k
R5
2
R
R6, R7

Prime Mover design files

The KiCad project lives in the dannyandreev/TheLittleRascal-Electrical repository on GitHub; these links point at the commit this page was built from.

Prime Mover: common questions

What microcontroller does the Prime Mover use?

The Prime Mover is built around the Raspberry_Pi_2_3, from the Raspberry Pi family.

How big is the Prime Mover PCB?

The Prime Mover measures 80.1 × 56 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Prime Mover?

37 components, from 24 distinct parts. The full bill of materials is listed on this page.

Where can I download the Prime Mover design files?

From the dannyandreev/TheLittleRascal-Electrical repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Prime Mover design in my own project?

Yes, under the terms of its MIT license, which dannyandreev chose for the repository.

Can I test firmware for the Prime Mover without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

More boards in TheLittleRascal-Electrical

Similar boards