HardLabs

PrimeMover

dannyandreev·TheLittleRascal-Electrical·Prime Mover V1.2/PrimeMover.kicad_pcb

PrimeMover PCB layout, top view — open source Raspberry Pi board by dannyandreev

About the PrimeMover PCB

PrimeMover is an open source Raspberry Pi PCB design by dannyandreev, published on GitHub under the MIT license. It is a 2-layer board measuring 10.7 × 14.7 mm, with 51 components from 27 distinct parts.

Its main chip is the Raspberry_Pi_2_3, from the Raspberry Pi family. Other key parts include the MCP3008-I_P, PCA9685PW and TXB0108PWR. By type, the board carries 18 connectors, 12 resistors, 11 capacitors, 4 ICs and 4 diodes.

Main components on the PrimeMover

MCP3008-I_PPCA9685PWTXB0108PWR

PrimeMover bill of materials (BOM)

51 components, 27 distinct parts.

QtyPartRefs
2
MCP3008-I_P
U1, U2
1
PCA9685PW
U4
1
TXB0108PWR
U5
1
Conn_01x08_Male
J1
1
Conn_01x09_Male
J2
3
Conn_01x02_Male
J3, J6, J8
2
Conn_01x04_Male
J4, J10
5
Conn_01x07_Male
J5, J13, J14, J15, J18
1
Conn_01x02_Female
J7
1
Conn_01x02_Male
J9
2
Conn_01x03_Male
J11, J12
1
Conn_01x06_Male
J16
1
Conn_01x02_Male
J17
1
FAN
FAN1
1
MP1584_3V3Module
PWR1
1
3V6
D1
3
LED
D2, D3, D4
8
0.1uF
C1, C2, C3, C4, C6, C8, C10, C11
3
27uF 16V
C5, C7, C9
1
Raspberry_Pi_2_3
R1
Show 7 more
QtyPartRefs
1
4.7k
R2
1
1.5k
R3
4
10k
R4, R5, R6, R7
1
470
R8
1
2k2
R9
1
3k3
R10
2
4k7
R11, R12

PrimeMover design files

The KiCad project lives in the dannyandreev/TheLittleRascal-Electrical repository on GitHub; these links point at the commit this page was built from.

PrimeMover: common questions

What microcontroller does the PrimeMover use?

The PrimeMover is built around the Raspberry_Pi_2_3, from the Raspberry Pi family.

How big is the PrimeMover PCB?

The PrimeMover measures 10.7 × 14.7 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the PrimeMover?

51 components, from 27 distinct parts. The full bill of materials is listed on this page.

Where can I download the PrimeMover design files?

From the dannyandreev/TheLittleRascal-Electrical repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the PrimeMover design in my own project?

Yes, under the terms of its MIT license, which dannyandreev chose for the repository.

Can I test firmware for the PrimeMover without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

More boards in TheLittleRascal-Electrical

Similar boards