24 open source boards using the TXB0108PWR
Real designs built with the TXB0108PWR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
JJ65c02
jimjag
172.7 × 135.9 mm47 parts4LMIT25MC60
wyolum
60 × 70 mm97 parts2LNo license17MicroZed carrier board
viktor-nikolov
124.5 × 135.4 mm76 parts6LCC0-1.07ESP32
Gpsrx
bgelb
152.4 × 92 mm283 parts6LNo license1EEG-I-LAB
Tahacrpc
101.6 × 53.3 mm139 parts4LCERN-OHL-1.21Rc2014 level shift
xunil
47 × 105.4 mm22 parts2LNo license1- schematic only · 1 parts
Level shifter shield
ajokela
1 partsNo license1 Arena 12-12 v8 ni
floesche
228.6 × 228.6 mm575 parts6LCC-BY-4.00RP2040/RP2350
PCE colorlight carrier
supermomo31
180 × 160 mm253 parts4LNo license0STM32
Flip phone
denglermoss
50 × 80 mm130 parts2LNo license0Raspberry Pi
PrimeMover
dannyandreev
10.7 × 14.7 mm51 parts2LMIT0Heartthingv2 ecg
kermitsgonnakermicide
25.8 × 28.7 mm30 parts2LNo license0AVR/Arduino
Addon board
b1uN7
78.6 × 84.6 mm22 parts2LNo license15NXP
Arena 12-12 Teensy Modular LED Display
floesche
228.6 × 228.6 mm441 parts6LCC-BY-4.00STM32
Sci board
MatthiasGeorgImhof
80 × 80 mm197 parts4LCC-BY-NC-4.00Raspberry Pi
RascalHat
dannyandreev
10.7 × 14.7 mm51 parts2LMIT0AVR/Arduino
WaveWise Buoy
GenerateNU
67.8 × 76.2 mm47 parts4LNo license0ESP32
Sailboard esp
rmcl
91.4 × 51.4 mm34 parts2LNo license0Nordic nRF
MCU V2
kermitsgonnakermicide
63 × 28 mm9 parts2LNo license0Arena 12-12 v7 ni
floesche
228.6 × 228.6 mm120 parts6LCC-BY-4.00AVR/Arduino
WaveWise Buoy
GenerateNU
67.8 × 76.2 mm47 parts4LNo license0NXP
12-12 Teensy G4.1 Arena Modular LED Display
floesche
228.6 × 228.6 mm119 parts6LCC-BY-4.00STM32
Sci board wo switches
MatthiasGeorgImhof
80 × 80 mm168 parts4LCC-BY-NC-4.00STM32
X1
embeddedalpha
30 × 80 mm57 parts2LMIT75
How designs wire the TXB0108PWR
Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the TXB0108PWR connects to, and the resistors, capacitors and other passives placed on it.
- The VCCB pin has a decoupling capacitor on 10 of 17 designs, most often 100 nF (then 1 µF).
- The OE pin has a pull-up to 3.3V on 9 of 17 designs, most often 10 kΩ (then 47 kΩ).
- The VCCA pin has a decoupling capacitor on 7 of 17 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCApin 2 | Connected to: 3.3V 100% |
|
| OEpin 10 | Connected to: Signal 53% · 3.3V 47% |
|
| GNDpin 11 | Connected to: GND 100% | — |
| VCCBpin 19 | Connected to: 5V 94% |
|
16 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include X1 by embeddedalpha, JJ65c02 by jimjag, MC60 by wyolum and Addon board by b1uN7.
The TXB0108PWR in open source designs
The gallery holds 24 open source boards using the TXB0108PWR from 18 GitHub repositories; a typical one measures about 80 × 80 mm and carries around 67 components.
57% use four copper layers or more, and 42% carry an open source license.
The most starred is X1 by embeddedalpha.
Parts used alongside the TXB0108PWR
Microcontrollers on boards using the TXB0108PWR
What boards using the TXB0108PWR are built for
TXB0108PWR: common questions
Where can I find a TXB0108PWR reference design?
Each of the 24 boards on this page is a real design using the TXB0108PWR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the TXB0108PWR VCCB pin?
The VCCB pin has a decoupling capacitor on 10 of 17 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 17 open source designs using the TXB0108PWR.
What pull-up resistor is used on the TXB0108PWR OE pin?
The OE pin has a pull-up to 3.3V on 9 of 17 designs, most often 10 kΩ (then 47 kΩ). Counted from the KiCad layouts of 17 open source designs using the TXB0108PWR.
What decoupling capacitors do designs use on the TXB0108PWR VCCA pin?
The VCCA pin has a decoupling capacitor on 7 of 17 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 17 open source designs using the TXB0108PWR.
What parts are used alongside the TXB0108PWR?
The ATMEGA328PB-ANR, AZ1117CH-3.3TRG1, FT232RL-REEL, LM2576HVS-5.0_NOPB and Pololu_DRV8711_Motor_Driver appear in the most repositories here.
Which microcontrollers do boards using the TXB0108PWR use?
Most are built on STM32 (4), AVR/Arduino (3), Raspberry Pi (2) and NXP (2).
How big is a typical board using the TXB0108PWR?
The median is 80 × 80 mm, and 43% are two-layer designs.
What is the most popular open source board using the TXB0108PWR?
By GitHub stars, X1 by embeddedalpha, with 75 stars.
Can I simulate one of these boards using the TXB0108PWR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.