Robodrive
dbking77·robodrive_pcb
About the Robodrive PCB
Robodrive is an open source ESP32 PCB design by dbking77, published on GitHub under the MIT license. It is a 2-layer board measuring 44.5 × 23 mm, with 24 components from 16 distinct parts.
Its main chip is the XIAO-ESP32-C6-DIP, from the ESP32 family. Other key parts include the TPS7B92050DBVR and DRV8871DDAR. By type, the board carries 8 resistors, 6 connectors, 6 capacitors and 4 ICs.
It belongs with the iot & wireless and robotics & motion designs in this gallery.
From the project
Dual brushed motor driver with wireless connectivity
- XL-302SURD : 600mcd @ 20mA - C503B-RAN-CZ0C0AA1 : 15000mcd @ 20mA 15degrees, 2.1Vf - (3.3V - 2.1V) / 1kOhm = 1.2mA --> 900 mcd - C503B-RCN-CW0Z0AA1 : 5100mcd @ 20mA 30degrees, 2.1Vf - (3.3V - 2.1V) / 1kOhm = 1.2mA --> 306 mcd
Itrip = 1.5 Amp : RLim (kOhm) = 64 / ITrip = 42kOhm Itrip = 1.64 Amp : RLip (kOhm) = 64 / ITrip = 39kOhm Itrip = 2.0 Amp : RLim (kOhm) = 64 / ITrip = 36kOhm

Main components on the Robodrive
Robodrive bill of materials (BOM)
24 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TPS7B92050DBVR | SOT-23-5 | U2 |
| 2 | DRV8871DDAR | hsop8_hole | U3, U4 |
| 1 | XIAO-ESP32-C6-DIP | XIAO-ESP32-C6-DIP-ONLY | U5 |
| 2 | Conn_01x03_Pin | PinHeader_1x03_P2.54mm_Horizontal | J2, J3 |
| 1 | MOTOR2 | PinHeader_1x02_P2.54mm_Horizontal | J4 |
| 1 | MOTOR1 | PinHeader_1x02_P2.54mm_Horizontal | J5 |
| 1 | POWER | PinHeader_1x02_P2.54mm_Horizontal | J6 |
| 1 | LED | PinHeader_1x02_P2.54mm_Horizontal | J7 |
| 1 | 100uF | CP_Radial_D6.3mm_P2.50mm | C1 |
| 4 | 1uF | C_0805_2012Metric | C2, C3, C12, C13 |
| 1 | 10000pf 16V | C_0603_1608Metric | C11 |
| 2 | TBD | R_0603_1608Metric | R1, R11 |
| 3 | 1k | R_0603_1608Metric | R2, R9, R10 |
| 1 | 56.2k | R_0603_1608Metric | R6 |
| 1 | 10k | R_0603_1608Metric | R7 |
| 1 | JUMPER | R_0603_1608Metric | R8 |
Robodrive design files
The KiCad project lives in the dbking77/robodrive_pcb repository on GitHub; these links point at the commit this page was built from.
- Layoutrobodrive_pcb.kicad_pcb
- Schematicrobodrive_pcb.kicad_sch
Robodrive: common questions
What microcontroller does the Robodrive use?
The Robodrive is built around the XIAO-ESP32-C6-DIP, from the ESP32 family.
How big is the Robodrive PCB?
The Robodrive measures 44.5 × 23 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Robodrive?
24 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the Robodrive design files?
From the dbking77/robodrive_pcb repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Robodrive design in my own project?
Yes, under the terms of its MIT license, which dbking77 chose for the repository.
Can I test firmware for the Robodrive without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k