13 open source boards using the DRV8871DDAR
Real designs built with the DRV8871DDAR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raspberry Pi
Openpayphone
eric-cgn
65 × 55 mm38 parts2LMIT13Robocar pinky
arkorobotics
81.3 × 52.8 mm83 parts4LNo license12RP2040/RP2350
Digits
justinlindh
61.9 × 76.2 mm74 parts2LAGPL-3.04TIGP class board 2026 - main board
TIGP-Experimental-Methods
180 × 100 mm318 parts4LNo license0FilMachine Mainboard
yesnoj
110 × 90 mm198 parts4LNo license0ESP32
Rallybot
lois-goon
100 × 80 mm103 parts4LMIT0ESP32
Esp32MC
mauimart
96 × 60 mm99 parts4LNo license0ESP32
Esp32-energy meter
kbssrikar7
160 × 110 mm76 parts2LNo license0Kamikazii
choicebuilds
75 × 49 mm55 parts4LNo license0ESP32
Robodrive
dbking77
44.5 × 23 mm24 parts2LMIT0TC DRIVE REVA
hankenken
100 × 100 mm35 parts2LNo license1TC DRIVE REVB
hankenken
60 × 45 mm35 parts2LNo license1AVR/Arduino
Slippi
RoboJackets
78.7 × 34.9 mm42 parts2LMIT9
How designs wire the DRV8871DDAR
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the DRV8871DDAR connects to, and the resistors, capacitors and other passives placed on it.
- The ILIM pin has a resistor to GND on 12 of 12 designs, most often 30 kΩ (then 16 kΩ).
- The VM pin has a decoupling capacitor on 7 of 12 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| ILIMpin 4 | Connected to: Signal 100% |
|
| VMpin 5 | Connected to: 12V 67% · a signal 33% |
|
| PGNDpin 7 | Connected to: GND 100% | — |
| PADpin 9 | Connected to: GND 100% | — |
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Openpayphone by eric-cgn, Robocar pinky by arkorobotics, Slippi by RoboJackets and Digits by justinlindh.
The DRV8871DDAR in open source designs
The gallery holds 13 open source boards using the DRV8871DDAR from 12 GitHub repositories; a typical one measures about 81.3 × 60 mm and carries around 74 components.
54% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is Openpayphone by eric-cgn.
Parts used alongside the DRV8871DDAR
Microcontrollers on boards using the DRV8871DDAR
What boards using the DRV8871DDAR are built for
DRV8871DDAR: common questions
Where can I find a DRV8871DDAR reference design?
Each of the 13 boards on this page is a real design using the DRV8871DDAR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the DRV8871DDAR ILIM pin?
The ILIM pin has a resistor to GND on 12 of 12 designs, most often 30 kΩ (then 16 kΩ). Counted from the KiCad layouts of 12 open source designs using the DRV8871DDAR.
What decoupling capacitors do designs use on the DRV8871DDAR VM pin?
The VM pin has a decoupling capacitor on 7 of 12 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 12 open source designs using the DRV8871DDAR.
What parts are used alongside the DRV8871DDAR?
The ADS1115IDGSR, AMS1117-3.3 and L7805CV appear in the most repositories here.
Which microcontrollers do boards using the DRV8871DDAR use?
Most are built on ESP32 (4), AVR/Arduino (1), Raspberry Pi (1) and RP2040/RP2350 (1).
How big is a typical board using the DRV8871DDAR?
The median is 81.3 × 60 mm, and 54% are two-layer designs.
What is the most popular open source board using the DRV8871DDAR?
By GitHub stars, Openpayphone by eric-cgn, with 13 stars.
Can I simulate one of these boards using the DRV8871DDAR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.