Macropad
DenisVargaeu·Macropad
About the Macropad PCB
Macropad is an open source RP2040/RP2350 PCB design by DenisVargaeu, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 56.3 × 94.8 mm, with 24 components from 7 distinct parts.
Its main chip is the RaspberryPi_Pico, from the RP2040/RP2350 family. Other key parts include the ER_OLEDM0.91_1x-I2C. By type, the board carries 16 switches, 3 resistors, 1 IC, 1 module, 1 connector and 1 diode.
It belongs with the keyboards and displays & leds designs in this gallery.
From the project
- 16 tactile keys in a 4×4 matrix — direct GPIO (no matrix scanning needed) - 0.91″ OLED display (128×32, SSD1306, I2C) — status, layers, animations - RGB LED (5 mm, common cathode) — per-key or global lighting - Raspberry Pi Pico / Pico 2 — RP2040 or RP2350, USB-C, BOOTSEL butto
- 16 tactile keys in a 4×4 matrix — direct GPIO (no matrix scanning needed) - 0.91″ OLED display (128×32, SSD1306, I2C) — status, layers, animations - RGB LED (5 mm, common cathode) — per-key or global lighting - Raspberry Pi Pico / Pico 2 — RP2040 or RP2350, USB-C, BOOTSEL button accessible - Through-hole only — easy hand soldering, beginner-friendly - Open hardware — CERN-OHL-P-2.0 license, modify freely
Main components on the Macropad
Macropad bill of materials (BOM)
24 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ER_OLEDM0.91_1x-I2C | ER_OLEDM0.91_1x-I2C | U1 |
| 1 | RaspberryPi_Pico | RaspberryPi_Pico_Common_Unspecified | A1 |
| 1 | Conn_01x06_Pin | PinHeader_1x06_P2.54mm_Horizontal | J1 |
| 1 | R_Potentiometer | Potentiometer_Alps_RK09K_Single_Vertical | RV1 |
| 16 | SW_Push | SW_PUSH_6mm | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +8 |
| 1 | LED_BKGR | LED_D5.0mm-4_RGB_Wide_Pins | D2 |
| 3 | R | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3 |
Macropad design files
The KiCad project lives in the DenisVargaeu/Macropad repository on GitHub; these links point at the commit this page was built from.
- Layoutmacropad.kicad_pcb
- Schematicmacropad.kicad_sch
Macropad: common questions
What microcontroller does the Macropad use?
The Macropad is built around the RaspberryPi_Pico, from the RP2040/RP2350 family.
How big is the Macropad PCB?
The Macropad measures 56.3 × 94.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Macropad?
24 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Macropad design files?
From the DenisVargaeu/Macropad repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Macropad design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which DenisVargaeu chose for the repository.
Can I test firmware for the Macropad without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.
Similar boards
RP2040/RP2350
OSO-BOOK-C1
joeycastillo
85 × 115 mm29 parts2LCC-BY-SA-4.08.1kRP2040/RP2350
Corne chocolate
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Corne cherry
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
LogicAnalyzer
gusmanb
57 × 55.2 mm6 parts2LGPL-3.05.0kRP2040/RP2350
Jitx design
gusmanb
55.5 × 65 mm26 parts4LGPL-3.05.0kRP2040/RP2350
Main
google
98 × 71 mm102 parts2LApache-2.02.9k