HardLabs

Nerf target v1

DIaLOGIKa-GmbH·modular-nerf-target·electronics/nerf-target-v1/nerf-target-v1.kicad_pcb

Nerf target v1 PCB layout, top view — open source RP2040/RP2350 board by DIaLOGIKa-GmbH

About the Nerf target v1 PCB

Nerf target v1 is an open source RP2040/RP2350 PCB design by DIaLOGIKa-GmbH, published on GitHub under the MIT license. It is a 2-layer board measuring 103.9 × 119.3 mm, with 51 components from 24 distinct parts.

Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the W25Q128JVS and M24C02-WMN. By type, the board carries 18 capacitors, 17 resistors, 9 diodes, 3 ICs, 1 transistor and 1 crystal.

From the project

A hex-based modular system to build custom nerf gun targets

Main components on the Nerf target v1

W25Q128JVSRP2040M24C02-WMN

Nerf target v1 bill of materials (BOM)

51 components, 24 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
W25Q128JVS
U1
1
RP2040
U2
1
M24C02-WMN
U5
1
S8050
Q1
1
X322512MSB4SI
Y1
1
CORTEXDEBUG10
CortexDebug10
J3
1
C233793
Goertek B4013AM422-42
MK1
3
C2286
red
D1, D4, D7
3
C84264
green
D2, D5, D8
3
C19171394
blue
D3, D6, D9
3
2U2
2u2
C1, C11, C21
11
100N
100n
C2, C3, C4, C5, C6, C7, C8, C9 +3
2
30P
33p
C14, C15
1
10U
10u
C16
1
2U2
1n
C17
6
220
R2, R3, R5, R6, R9, R10
3
120
R4, R8, R11
1
2K2
2k2
R7
2
4K7
4k7
R12, R13
1
470
R14
Show 4 more
QtyPartRefs
1
2k2
R15
1
100k
R16
1
82k
R17
1
20k
R18

Nerf target v1 design files

The KiCad project lives in the DIaLOGIKa-GmbH/modular-nerf-target repository on GitHub; these links point at the commit this page was built from.

Nerf target v1: common questions

What microcontroller does the Nerf target v1 use?

The Nerf target v1 is built around the RP2040, from the RP2040/RP2350 family.

How big is the Nerf target v1 PCB?

The Nerf target v1 measures 103.9 × 119.3 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Nerf target v1?

51 components, from 24 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Nerf target v1 design files?

From the DIaLOGIKa-GmbH/modular-nerf-target repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Nerf target v1 design in my own project?

Yes, under the terms of its MIT license, which DIaLOGIKa-GmbH chose for the repository.

Can I test firmware for the Nerf target v1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in modular-nerf-target

Similar boards