Schematic
DrGlaucous·FightingRobot·RB3/Schematic/Schematic/Schematic.kicad_pcb
About the Schematic PCB
Schematic is an open source ESP32 PCB design by DrGlaucous, published on GitHub. It is a 2-layer board measuring 47.6 × 33 mm, with 9 components from 8 distinct parts.
Its main chip is the ESP32-C3-SuperMini_PLUS, from the ESP32 family. Other key parts include the Mini360. By type, the board carries 5 connectors, 3 ICs and 1 switch.
From the project
Use RFM69 to transmit PPM cheaply
Main components on the Schematic
Schematic bill of materials (BOM)
9 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | ESP32-C3-SuperMini_PLUS | U1 |
| 1 | ~ | HW-627 | U2 |
| 1 | Mini360 | Mini360 | U3 |
| 2 | Motor 1 | PinHeader_1x06_P2.54mm_Vertical | J1, J2 |
| 1 | Battery | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | ESC | PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | ESC_PWR | PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | MAIN_CUTOFF | PinHeader_1x02_P2.54mm_Vertical | SW1 |
Schematic design files
The KiCad project lives in the DrGlaucous/FightingRobot repository on GitHub; these links point at the commit this page was built from.
Schematic: common questions
What microcontroller does the Schematic use?
The Schematic is built around the ESP32-C3-SuperMini_PLUS, from the ESP32 family.
How big is the Schematic PCB?
The Schematic measures 47.6 × 33 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Schematic?
9 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Schematic design files?
From the DrGlaucous/FightingRobot repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Schematic design in my own project?
The repository has no license, so all rights stay with DrGlaucous. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Schematic without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in FightingRobot
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k