G4 Controller Board
DrGlaucous·G4·Schematic/G4_Controller_Board_Wide_Layout(OLD)/G4_Controller_Board_Wide_Layout.kicad_pcb
About the G4 Controller Board
G4 Controller Board is an open source ESP32 PCB design by DrGlaucous, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 58.4 × 33 mm, with 27 components from 25 distinct parts.
Its main chip is the ESP32-LOLIN32-Lite, from the ESP32 family. Other key parts include the Mini360. By type, the board carries 16 connectors, 5 resistors, 2 ICs, 1 transistor, 1 buzzer and 1 jumper.
It belongs with the displays & leds designs in this gallery.
From the project
Governor G4
This is a repo for a low-cost and feature-rich "flywheel-type" nerf blaster.
Features/Speficications: - Goal build cost < 150$ - Minimal plastic-anchored screws (almost evertthing is secured with bolts + captive nuts) - Brushless motor flyhweels - Solenoid pusher - LCD display - Angled talon compatability (straight stick support planned) - Integrated ammo counter hardware - Integrated chronograph hardware - 3-5S Lipo compatable - 6cm flywheel diameter - ESP32 controller - Closed-loop flywheel control (providing fixed RPM and fast spinup times) - Through-hole electronics and soldering - Fast…
Main components on the G4 Controller Board
G4 Controller Board bill of materials (BOM)
27 components, 25 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Mini360 | Mini360 | U1 |
| 1 | ESP32-LOLIN32-Lite | ESP32-LOLIN32-Lite | U2 |
| 1 | IRF540N | TO-220-3_Vertical | Q1 |
| 1 | Solenoid | PinHeader_1x02_P2.54mm_Vertical | J5 |
| 2 | Fire Trigger | PinSocket_1x02_P2.54mm_Vertical | J6, J15 |
| 1 | 12 Volts In | PinSocket_1x02_P2.54mm_Vertical | J9 |
| 1 | Preset A | PinSocket_1x02_P2.54mm_Vertical | J10 |
| 1 | Preset B | PinSocket_1x02_P2.54mm_Vertical | J11 |
| 1 | Preset C | PinSocket_1x02_P2.54mm_Vertical | J12 |
| 1 | Combined Preset Connector | PinSocket_1x04_P2.54mm_Vertical | J13 |
| 1 | Rev Trigger (Optional) | PinSocket_1x02_P2.54mm_Vertical | J14 |
| 1 | Magazine Removal Trigger | PinSocket_1x02_P2.54mm_Vertical | J16 |
| 1 | Rotary Encoder | PinSocket_1x05_P2.54mm_Vertical | J17 |
| 1 | I2C Out | PinSocket_1x04_P2.54mm_Vertical | J18 |
| 1 | ESC Right | PinHeader_1x03_P2.54mm_Vertical | J19 |
| 1 | ESC Left | PinHeader_1x03_P2.54mm_Vertical | J20 |
| 1 | IR LED Rec. | PinHeader_1x03_P2.54mm_Vertical | J23 |
| 1 | IR LED Emitter | PinSocket_1x02_P2.54mm_Vertical | J24 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Jumper_3_Bridged12 | SolderJumper-3_P1.3mm_Open_Pad1.0x1.5mm | JP1 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | IN4001 | D_DO-41_SOD81_P7.62mm_Horizontal | D1 |
| 1 | 220 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 2 | 2.4k Ohm | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R3 |
| 1 | 10K Ohm | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
| 1 | 90 Ohm | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5 |
G4 Controller Board design files
The KiCad project lives in the DrGlaucous/G4 repository on GitHub; these links point at the commit this page was built from.
G4 Controller Board: common questions
What microcontroller does the G4 Controller Board use?
The G4 Controller Board is built around the ESP32-LOLIN32-Lite, from the ESP32 family.
How big is the G4 Controller Board?
The G4 Controller Board measures 58.4 × 33 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the G4 Controller Board?
27 components, from 25 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the G4 Controller Board design files?
From the DrGlaucous/G4 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the G4 Controller Board design in my own project?
Yes, under the terms of its GPL-3.0 license, which DrGlaucous chose for the repository.
Can I test firmware for the G4 Controller Board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in G4
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k