EthernetModule
Duet3D·Duet-2-Hardware·Ethernet_Module/EthernetModule.kicad_pcb
About the EthernetModule PCB
EthernetModule is an open source NXP PCB design by Duet3D, published on GitHub under the CERN-OHL-1.2 license. It is a 2-layer board measuring 37.4 × 33.8 mm, with 36 components from 21 distinct parts.
Its main chip is the LPC1768, from the NXP family. By type, the board carries 15 resistors, 14 capacitors, 3 connectors, 2 inductors, 1 IC and 1 crystal.
From the project
The KiCAD source for the Duet 3d printer controller see www.duet3d.com
The Duet 2 3D Printer Controller design files repository.
For hardware ourhcases see https://www.duet3d.com/
Duet Hardware runs RepRapFirmware: https://github.com/Duet3D/RepRapFirmware
Documentation: https://docs.duet3d.com/Duet3Dhardware/Duet2_family
Design by Tony Lock and David Crocker More info: https://www.duet3d.com/ LICENSE: see the LICENSE file in the repository
Main components on the EthernetModule
EthernetModule bill of materials (BOM)
36 components, 21 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LPC1768 W5500 | LQFP-48_7x7mm_Pitch0.5mm | U1 |
| 1 | 25MHZ CRYSTAL_4PIN | Xtal_5x3.2 | X1 |
| 1 | CONN2X20 RJ45+MAG | RJ45+MAG | J1 |
| 1 | CONN2X13 CONN_ALT_HEADER | CONN_ALT_HEADER_th | J2 |
| 1 | I2C_2 C_GND | 2.8mm_Spade_terminal | J3 |
| 2 | L_MINI | R_0603 | L1, L2 |
| 3 | 0u1 | C_0603 | C1, C2, C3 |
| 2 | 10uF/16V | C_1206_pol | C4, C5 |
| 2 | 6n8 | C_0603 | C6, C7 |
| 1 | 22n | C_0603 | C8 |
| 2 | 10n | C_0603 | C9, C11 |
| 1 | 4u7 | C_0603 | C10 |
| 1 | 0u01 +200V | C_0603 | C12 |
| 2 | 18p | C_0603 | C13, C14 |
| 2 | 1M | R_0603 | R1, R10 |
| 1 | 4K7 | R_0603 | R2 |
| 4 | 49R9 | R_0603 | R3, R4, R12, R13 |
| 1 | 10R | R_0603 | R5 |
| 4 | 33R | R_0603 | R6, R7, R8, R9 |
| 2 | 220R | R_0603 | R11, R15 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 12K4 | R_0603 | R16 |
EthernetModule design files
The KiCad project lives in the Duet3D/Duet-2-Hardware repository on GitHub; these links point at the commit this page was built from.
EthernetModule: common questions
What microcontroller does the EthernetModule use?
The EthernetModule is built around the LPC1768, from the NXP family.
How big is the EthernetModule PCB?
The EthernetModule measures 37.4 × 33.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the EthernetModule?
36 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the EthernetModule design files?
From the Duet3D/Duet-2-Hardware repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the EthernetModule design in my own project?
Yes, under the terms of its CERN-OHL-1.2 license, which Duet3D chose for the repository.
Can I test firmware for the EthernetModule without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.
More boards in Duet-2-Hardware
ESP32
Duet 2
Duet3D
100 × 123 mm348 partsCERN-OHL-1.2258ESP8266
Duet WIFI
Duet3D
100 × 123 mm345 partsCERN-OHL-1.2258Microchip SAM
Duet 2 Maestro
Duet3D
100 × 123 mm336 partsCERN-OHL-1.2258NXP
Duex5
Duet3D
100 × 123 mm252 partsCERN-OHL-1.2258NXP
DuetEthernet
Duet3D
37.5 × 33.8 mm36 parts2LCERN-OHL-1.2258NXP
Expansion Breakout
Duet3D
88.5 × 28 mm22 partsCERN-OHL-1.2258
Similar boards
NXP
32Bit shift register
MaltWhiskey
100 × 54 mm56 parts4LNo license763NXP
Mega-Cube-Board
MaltWhiskey
200 × 54 mm100 parts4LNo license763NXP
MCL6809
MicroCoreLabs
32.3 × 61 mm7 parts4LNo license532NXP
MCL68
MicroCoreLabs
31.6 × 84.1 mm13 parts4LNo license532NXP
MCL65+
MicroCoreLabs
72.6 × 64.1 mm6 parts2LNo license532NXP
MCLZ8
MicroCoreLabs
37.1 × 61.5 mm6 parts4LNo license532