Smarthome-Hardware
Dungeons-of-dragons·smarthome-Hardware·PCB design/Home.kicad_pcb
About the Smarthome-Hardware PCB
Smarthome-Hardware is an open source ESP32 PCB design by Dungeons-of-dragons, published on GitHub. It is a 2-layer board measuring 104.8 × 168.9 mm, with 22 components from 20 distinct parts.
Its main chip is the MODULE_ESP32_DEVKIT_V1, from the ESP32 family. Other key parts include the ACS712, DHT11, PIR and MQ2. By type, the board carries 8 connectors, 4 ICs, 2 resistors, 1 buzzer, 1 relay and 1 switch.
It belongs with the iot & wireless, sensors and power & battery designs in this gallery.
From the project
This holds our PCB schematics and PCB design.
This repo holds our PCB schematics and PCB design and is used for version control of PCBs.
The directory holds the ProjectLibraries** and schematics and PCB design.
Thr Project Libraries folder contains custom symbols and footprints of the sensors used. The component used can be found within the Home.csv file. that is the BOM.
The components needed to replicate this PCB and project are:

Main components on the Smarthome-Hardware
Smarthome-Hardware bill of materials (BOM)
22 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ACS712 | ACS712_5B | U1 |
| 1 | DHT11 | DHT11_KY-015 | U3 |
| 1 | PIR | PIR_HC-S501 | U5 |
| 1 | MQ2 | MQ2 | U6 |
| 1 | Fan | TerminalBlock_Altech_AK300-3_P5.00mm | J1 |
| 1 | LCD | TerminalBlock_Altech_AK300-2_P5.00mm | J2 |
| 1 | EM lock | TerminalBlock_Altech_AK300-2_P5.00mm | J3 |
| 1 | ACS712 Signal | TerminalBlock_Altech_AK300-2_P5.00mm | J4 |
| 1 | Power In | TerminalBlock_Altech_AK300-2_P5.00mm | J5 |
| 1 | LCD | TerminalBlock_Altech_AK300-3_P5.00mm | J6 |
| 2 | RFID | TerminalBlock_Altech_AK300-3_P5.00mm | J7, J8 |
| 1 | Buzzer | Buzzer_D14mm_H7mm_P10mm | BZ1 |
| 1 | ~ | MODULE_ESP32_DEVKIT_V1 | ESP32_DEVKIT_V1 |
| 1 | SANYOU_SRD_Form_C | Relay_SPDT_SANYOU_SRD_Series_Form_C | K1 |
| 1 | 5V | LM2596_module | LM2596_buck_converter1 |
| 1 | 3.3V | LM2596_module | LM2596_buck_converter2 |
| 1 | SW_SPST | SPST - KCD1-11 | SW1 |
| 1 | LED_RGBK | RGB_LED | D1 |
| 1 | C | C_Disc_D3.8mm_W2.6mm_P2.50mm | C1 |
| 2 | R | R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1, R2 |
Smarthome-Hardware design files
The KiCad project lives in the Dungeons-of-dragons/smarthome-Hardware repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB design/Home.kicad_pcb
- SchematicPCB design/Home.kicad_sch
Smarthome-Hardware: common questions
What microcontroller does the Smarthome-Hardware use?
The Smarthome-Hardware is built around the MODULE_ESP32_DEVKIT_V1, from the ESP32 family.
How big is the Smarthome-Hardware PCB?
The Smarthome-Hardware measures 104.8 × 168.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Smarthome-Hardware?
22 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the Smarthome-Hardware design files?
From the Dungeons-of-dragons/smarthome-Hardware repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Smarthome-Hardware design in my own project?
The repository has no license, so all rights stay with Dungeons-of-dragons. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Smarthome-Hardware without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k