Probe wink

dwzg·probe-wink·pcb/probe-wink.kicad_pcb

Probe wink PCB layout, top view — open source ESP32 board by dwzg

About the Probe wink PCB

Probe wink is an open source ESP32 PCB design by dwzg, published on GitHub under the MIT license. It is a 2-layer board measuring 46 × 40 mm, with 48 components from 29 distinct parts.

Its main chip is the ESP32-C3-WROOM-02-N4, from the ESP32 family. Other key parts include the LMR16006XDDCR. By type, the board carries 18 resistors, 13 capacitors, 7 diodes, 3 transistors, 2 ICs and 2 connectors.

From the project

One module per headlamp. 46 × 40 mm, 2 layers, ESP32-C3-WROOM-02 (or -02U with an external antenna: same pads) with the antenna overhanging the right edge, TE IM06GR swap relay, LMR16006X buck from the retractor's own 12 V feed. The module connects through a 6-wire lead to a Y-ad

One module per headlamp. 46 × 40 mm, 2 layers, ESP32-C3-WROOM-02 (or -02U with an external antenna: same pads) with the antenna overhanging the right edge, TE IM06GR swap relay, LMR16006X buck from the retractor's own 12 V feed. The module connects through a 6-wire lead to a Y-adapter between the factory retractor plug and socket; motor current stays in the adapter.

Main components on the Probe wink

Probe wink bill of materials (BOM)

48 components, 29 distinct parts.

QtyPartRefs
1
LMR16006XDDCR
U1
1
ESP32-C3-WROOM-02-N4
U2
1
MMBTA06LT1G (80 V NPN)
MMBTA06
Q1
2
2N7002
Q2, Q3
1
sheathed 6 x 0.5 mm2 lead (LiYY 6x0.5)
CAR
J1
1
bare pads on the back behind the module: pogo clip
BOOT
J2
1
SIDE
JP1
1
IM06GR (TE), alt HFD4/12-SR C44212
IM06GR
K1
1
M7
D1
1
SMCJ30A (Littelfuse)
SMCJ30A
D2
1
PMEG10010ELRX
PMEG10010ELR
D3
1
1N4148W
D4
1
NCD0805R1
red
D5
2
BZT52C12S
D6, D7
1
SWPA5040S220MT
22u
L1
2
CC1206KKX7R0BB225
2.2u
C1, C11
1
CL21B104KCFNNNE
100n
C2
5
CC0805KRX7R9BB104
100n
C3, C6, C8, C9, C10
3
CL21B106KAYQNNE
10u
C4, C5, C13
1
CL21B105KBFNNNE
1u
C7
Show 9 more
QtyPartRefs
1
RVT63V22M6X5
22u
C12
5
0805W8F3303T5E
330k
R1, R3, R9, R17, R18
2
0805W8F2203T5E
220k
R2, R4
1
0805W8F2201T5E
2.2k
R5
3
0805W8F1003T5E
100k
R6, R8, R10
1
0805W8F1001T5E
1k
R7
4
0805W8F1002T5E
10k
R11, R12, R13, R14
1
0805W8F1004T5E
1M
R15
1
0805W8F6802T5E
68k
R16

Probe wink design files

The KiCad project lives in the dwzg/probe-wink repository on GitHub; these links point at the commit this page was built from.

Probe wink: common questions

What microcontroller does the Probe wink use?

The Probe wink is built around the ESP32-C3-WROOM-02-N4, from the ESP32 family.

How big is the Probe wink PCB?

The Probe wink measures 46 × 40 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Probe wink?

48 components, from 29 distinct parts. The full bill of materials is listed on this page.

Where can I download the Probe wink design files?

From the dwzg/probe-wink repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Probe wink design in my own project?

Yes, under the terms of its MIT license, which dwzg chose for the repository.

Can I test firmware for the Probe wink without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards