Wiimote ir sensor inline
eatnooM·pixart-sensor-adapter·inline/wiimote-ir-sensor-inline.kicad_pcb
About the Wiimote ir sensor inline PCB
Wiimote ir sensor inline is an open source PCB design by eatnooM, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 13 × 22.5 mm, with 10 components from 8 distinct parts.
Other key parts include the AP2112-3.3V. By type, the board carries 3 capacitors, 3 resistors, 2 ICs, 1 crystal and 1 connector.
It belongs with the sensors designs in this gallery.
From the project
Board to allow interfacing with a Wiimote camera over I2C for light guns
Allows interfacing with a Wiimote camera over I2C for GUN4IR.
Variants are present to allow use of the module either socketed as you'd find it on the Wiimote, or unsocketed for more compact installs.
I've only clocked a few hours actually using these, so run this off at your own risk.
The inline board should be ordered in 0.8mm thickness, otherwise you won't be able to solder to the pads on the camera! If ordering from OSHPark, I'd recommend the panelised version as they tend to put panel tabs on the edge connectors which can make for annoying cleanup before the boards are usable.
Main components on the Wiimote ir sensor inline
Wiimote ir sensor inline bill of materials (BOM)
10 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | wiimote-pixart-camera-inline_slim | U1 |
| 1 | AP2112-3.3V | SOT-23-5 | U2 |
| 1 | SG3225CAN 24.0000M-TJGA3 | Oscillator_SMD_SeikoEpson_SG8002CE-4Pin_3.2x2.5mm_HandSoldering | X1 |
| 1 | Conn_01x05_Pin | 5Wires-staggered | J1 |
| 1 | 0.1UF 0.1uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1 |
| 2 | 1UF 1uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3 |
| 2 | 2.7K | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 1 | 33K | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
Wiimote ir sensor inline design files
The KiCad project lives in the eatnooM/pixart-sensor-adapter repository on GitHub; these links point at the commit this page was built from.
Wiimote ir sensor inline: common questions
How big is the Wiimote ir sensor inline PCB?
The Wiimote ir sensor inline measures 13 × 22.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Wiimote ir sensor inline?
10 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Wiimote ir sensor inline design files?
From the eatnooM/pixart-sensor-adapter repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Wiimote ir sensor inline design in my own project?
Yes, under the terms of its CC-BY-SA-4.0 license, which eatnooM chose for the repository.
More boards in pixart-sensor-adapter
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2kSensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kPots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956