Wireless tank sensor
eburi·wireless-tank-sensor·hardware/kali-tank-sensor-v3/kali-tank-sensor-v3.kicad_pcb
About the Wireless tank sensor PCB
Wireless tank sensor is an open source ESP32 PCB design by eburi, published on GitHub under the MIT license. It is a 4-layer board measuring 55 × 52 mm, with 22 components from 20 distinct parts.
Its main chip is the 113991054, from the ESP32 family. Other key parts include the INA238AIDGSR and 3V3 5-30V. By type, the board carries 6 resistors, 4 connectors, 4 capacitors, 3 ICs, 2 diodes and 1 transistor.
It belongs with the iot & wireless, sensors and rf & radio designs in this gallery.
From the project
ESPHome/BTHome based wireless tank sensor.
A sealed, potted, maintenance-free water tank level sensor for boats (or caravans, cabins, anything with a resistive tank sender and a 12 V bus). It runs on a Seeed XIAO ESP32-C3, measures the plain old resistive float sender, works out the level itself, and shouts the result at Home Assistant over Bluetooth (BTHome v2).
You run two wires (12 V and ground) to the tank. That's it. No gauge, no Wi-Fi at the tank, no app, no cloud. Everything else happens in the Home Assistant box you already have on board.
Main components on the Wireless tank sensor
Wireless tank sensor bill of materials (BOM)
22 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 113991054 XIAO ESP32-C3 | XIAO-ESP32C3_TopSolder | U1 |
| 1 | INA238AIDGSR | MSOP-10_3x3mm_P0.5mm | U2 |
| 1 | 3V3 5-30V | DCDC_Module_18x12_4pad | U3 |
| 1 | AO3400A | SOT-23 | Q1 |
| 1 | 12V IN + | WirePad_StrainRelief | J1 |
| 1 | 12V IN - | WirePad_StrainRelief | J2 |
| 1 | SENDER A | WirePad_StrainRelief | J3 |
| 1 | SENDER B | WirePad_StrainRelief | J4 |
| 1 | PTC 200mA | R_1206_3216Metric | F1 |
| 1 | 3V3 FEED | SolderBridge_2pad | SB1 |
| 1 | SS34 | D_SMA | D1 |
| 1 | SMBJ16A | D_SMB | D2 |
| 1 | 100nF | C_0805_2012Metric | C1 |
| 2 | 22uF | C_1206_3216Metric | C2, C3 |
| 1 | 100nF/50V | C_0805_2012Metric | C4 |
| 1 | 1R 0.1% | R_0805_2012Metric | R1 |
| 1 | 100R | R_0805_2012Metric | R2 |
| 1 | 100R | R_0805_2012Metric | R3 |
| 1 | 100K 100k | R_0805_2012Metric | R4 |
| 2 | 4K7 4k7 | R_0805_2012Metric | R5, R6 |
Wireless tank sensor design files
The KiCad project lives in the eburi/wireless-tank-sensor repository on GitHub; these links point at the commit this page was built from.
Wireless tank sensor: common questions
What microcontroller does the Wireless tank sensor use?
The Wireless tank sensor is built around the 113991054, from the ESP32 family.
How big is the Wireless tank sensor PCB?
The Wireless tank sensor measures 55 × 52 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Wireless tank sensor?
22 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Wireless tank sensor design files?
From the eburi/wireless-tank-sensor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Wireless tank sensor design in my own project?
Yes, under the terms of its MIT license, which eburi chose for the repository.
Can I test firmware for the Wireless tank sensor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k