19 open source boards using the INA238AIDGSR
Real designs built with the INA238AIDGSR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
ESPHome-Indoor-Multi-Sensor
mikelawrence
52.5 × 59.7 mm97 parts4LCERN-OHL-P-2.012Raspberry Pi
HydroBall
CIDCO-dev
75.9 × 105.9 mm51 parts4LMIT11ESP32
Benchpod
embeddedci-com
82 × 90 mm306 parts4LCERN-OHL-W-2.01ESP32
Esphome rgbcct led controller
mikelawrence
100 × 45 mm82 parts6LCERN-OHL-P-2.01ESP32
Pajoniiir-M1
dvucinozd
175.6 × 220.1 mm223 parts4LNo license0ESP32
EU-LITE / routed draft
nikolajevs
100 × 100 mm158 parts4LNo license0ESP32
Atx-24pin rev3-candidate
nathanfraske
86 × 95 mm126 parts6LApache-2.00ESP32
Wireless tank sensor
eburi
55 × 52 mm22 parts4LMIT0ESP32
EU-LITE / routed draft
nikolajevs
100 × 100 mm158 parts4LNo license0ESP32
Eps-8pin rev3
nathanfraske
96 × 40 mm63 parts4LApache-2.00ESP32
Pcie3-rev2
nathanfraske
103.4 × 44 mm54 parts4LApache-2.00ESP32
Pcie3-rev2-routed
nathanfraske
103.4 × 44 mm54 parts4LApache-2.00ESP32
CEC PCIe 8-pin 3-Port Module
nathanfraske
103.4 × 56 mm54 parts4LApache-2.00ESP32
Esp32 ina238
HeyPCB
30 × 60 mm26 parts4LCERN-OHL-S-2.00ESP32
Build final
nathanfraske
96.1 × 43.7 mm45 parts4LApache-2.00ESP32
Eps rev3-n2
nathanfraske
96.1 × 43.7 mm45 parts4LApache-2.00ESP32
Pcie2-inrow
nathanfraske
86.4 × 44 mm45 parts4LApache-2.00ESP32
Pcie2-inrow routed
nathanfraske
86.4 × 44 mm45 parts4LApache-2.00ESP32
CEC PCIe 8-pin 2-Port Module
nathanfraske
86.4 × 44 mm45 parts4LApache-2.00
How designs wire the INA238AIDGSR
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the INA238AIDGSR connects to, and the resistors, capacitors and other passives placed on it.
- The A1 pin is tied to GND on 10 of 10 designs.
- The SDA pin has a pull-up to 3.3V on 8 of 10 designs, most often 4.7 kΩ (then 5.1 kΩ).
- The SCL pin has a pull-up to 3.3V on 8 of 10 designs, most often 4.7 kΩ (then 5.1 kΩ).
- The VS pin has a decoupling capacitor on 8 of 10 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| A1pin 1 | Connected to: GND 100% | — |
| A0pin 2 | Connected to: GND 90% | — |
| ALERTpin 3 | Connected to: Not connected 70% · a signal 30% | — |
| SDApin 4 | Connected to: The microcontroller 80%, a connector 20%, INA238AIDGSR 20% |
|
| SCLpin 5 | Connected to: The microcontroller 80%, a connector 20%, INA238AIDGSR 20% |
|
| VSpin 6 | Connected to: 3.3V 90% |
|
| GNDpin 7 | Connected to: GND 100% | — |
| VIN-pin 9 | Connected to: A connector 40% |
|
| VIN+pin 10 | Connected to: A connector 20% · GND 20% · 3.3V 30% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ESPHome-Indoor-Multi-Sensor by mikelawrence, HydroBall by CIDCO-dev, Benchpod by embeddedci-com and Esphome rgbcct led controller by mikelawrence.
The INA238AIDGSR in open source designs
The gallery holds 19 open source boards using the INA238AIDGSR from 10 GitHub repositories; a typical one measures about 96 × 52 mm and carries around 54 components.
100% use four copper layers or more, and 84% carry an open source license.
The most starred is ESPHome-Indoor-Multi-Sensor by mikelawrence.
Parts used alongside the INA238AIDGSR
Microcontrollers on boards using the INA238AIDGSR
What boards using the INA238AIDGSR are built for
INA238AIDGSR: common questions
Where can I find a INA238AIDGSR reference design?
Each of the 19 boards on this page is a real design using the INA238AIDGSR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the INA238AIDGSR A1 pin connected?
The A1 pin is tied to GND on 10 of 10 designs. Counted from the KiCad layouts of 10 open source designs using the INA238AIDGSR.
What pull-up resistor is used on the INA238AIDGSR SDA pin?
The SDA pin has a pull-up to 3.3V on 8 of 10 designs, most often 4.7 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 10 open source designs using the INA238AIDGSR.
What pull-up resistor is used on the INA238AIDGSR SCL pin?
The SCL pin has a pull-up to 3.3V on 8 of 10 designs, most often 4.7 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 10 open source designs using the INA238AIDGSR.
What parts are used alongside the INA238AIDGSR?
The USBLC6-2SC6, ESP32-WROOM-32E-N4, LM3429MH/NOPB, MCP7940N-I/SN and ST1S10PHR appear in the most repositories here.
Which microcontrollers do boards using the INA238AIDGSR use?
Most are built on ESP32 (18) and Raspberry Pi (1).
How big is a typical board using the INA238AIDGSR?
The median is 96 × 52 mm, and 0% are two-layer designs.
What is the most popular open source board using the INA238AIDGSR?
By GitHub stars, ESPHome-Indoor-Multi-Sensor by mikelawrence, with 12 stars.
Can I simulate one of these boards using the INA238AIDGSR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.