LiPo Charger 1
EE403-CapStone·Power·403_charger_v1/LiPo_Charger_1.kicad_pcb
About the LiPo Charger 1 PCB
LiPo Charger 1 is an open source PCB design by EE403-CapStone, published on GitHub. It is a 2-layer board measuring 34.9 × 27.8 mm, with 23 components from 18 distinct parts.
Other key parts include the FS312F-G, TP4056_[C16581] and MT3608. By type, the board carries 7 resistors, 4 capacitors, 3 ICs, 3 connectors, 3 diodes and 1 transistor.
It belongs with the power & battery designs in this gallery.
From the project
Design files of power
The circuit consists of 3 main circuits: the charging circuit, the protection circuit, and the boost circuit. Details of all components in the schematic will be shown below.
Three different track widths are used in the PCB design. They are 0.250mm, 0.500mm, and 0.750mm. The track of 0.250mm is used to transfer the signals around the chips. The track of 0.500 mm is used to connect pins involved with the output of the battery. The track of 0.750mm is used to be paths involved with boosted output. Additionally, two copper pour planes of GND are on the front and the back.

Main components on the LiPo Charger 1
LiPo Charger 1 bill of materials (BOM)
23 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | FS312F-G | SOT-23-6 | IC1 |
| 1 | TP4056_[C16581] | SOP-8_EP_150MIL | U1 |
| 1 | MT3608 | SOT-23-6 | U2 |
| 1 | FS8205 | SOT-23-6 | Q1 |
| 2 | USB_B_Micro | USB_Micro-B_Amphenol_10103594-0001LF_Horizontal | J1, J3 |
| 1 | Conn_01x02_Female | PinHeader_1x02_P1.00mm_Vertical | J2 |
| 1 | SW_DIP_x01 | SW_500SSP3S1M6QEA | SW1 |
| 1 | SS34_mdd | SS34_mdd | D1 |
| 1 | LED_R | 0603_LED_S1 | D2 |
| 1 | LED_G | 0603_LED_S1 | D3 |
| 1 | 22uH | 75_75_4 | L1 |
| 1 | 0.1u | 0603_R | C1 |
| 1 | 10u | 0603_R | C2 |
| 2 | 22uF | C_1206_3216Metric | C3, C4 |
| 2 | 2k | 0603_R | R1, R3 |
| 1 | 100 | 0603_R | R2 |
| 1 | 7.5k | 0603_R | R4 |
| 3 | 1k | 0603_R | R5, R6, R7 |
LiPo Charger 1 design files
The KiCad project lives in the EE403-CapStone/Power repository on GitHub; these links point at the commit this page was built from.
LiPo Charger 1: common questions
How big is the LiPo Charger 1 PCB?
The LiPo Charger 1 measures 34.9 × 27.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the LiPo Charger 1?
23 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the LiPo Charger 1 design files?
From the EE403-CapStone/Power repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the LiPo Charger 1 design in my own project?
The repository has no license, so all rights stay with EE403-CapStone. Use it as a reference, and ask the author before reusing the design.
More boards in Power
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1k