225 open source boards using the MT3608
Real designs built with the MT3608, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
USBSID-Pico
LouDnl
92.8 × 71.8 mm83 parts2LGPL-2.0125STM32
VNA
profdc9
100 × 85 mm178 parts2LNo license92AVR/Arduino
OTTOtact
cester-ino
307 × 131.2 mm224 parts2LGPL-3.049STM32
Oomwoo
makerspet
146.1 × 105.2 mm380 parts4LApache-2.042PWNSAT
ElectronicCats
83 × 83 mm114 parts4LNo license35ESP8266
Forcegauge
szbeni
60 × 40 mm69 parts2LGPL-3.018AM32 AI8051U
Icey7122
68.5 × 84.2 mm110 parts2LNo license15Raspberry Pi
Sensor
chukhanhhoang
64.8 × 62 mm61 parts2LNo license14AVR/Arduino
Avr transistor tester
vitaliy-bobrov
77.2 × 67.9 mm63 parts2LNo license11Badge Bugcon 2025
ElectronicCats
3.8 × 3.7 mm160 parts2LNo license9ESP32
Blinky badge light
rowr111
108.6 × 87.8 mm105 parts4LMIT9Kicad sailframes b1
sailframes
79.8 × 89.3 mm71 parts2LApache-2.07STM32
Printer otter
Jana-Marie
36 × 32 mm48 parts2LNo license7AVR/Arduino
BoardGame
jkordek1
150 × 150 mm176 parts2LNo license5ESP32
Plc board
denorath-sys
100 × 80 mm62 parts4LCERN-OHL-W-2.05- schematic only · 53 partsSTM32
Wmd6c servo
ChipCreates
53 partsMIT5 AVR/Arduino
PiSupply
enwi
65 × 56.5 mm67 parts2LLGPL-3.04Raspberry Pi
Gameboy dmg
alxhoff
82.5 × 87.5 mm52 parts2LGPL-3.04AVR/Arduino
RaspberryPi UPS HAT
gvoigtlaender
65 × 56 mm52 parts2LGPL-3.04STM32
USB-DALI
even-notodd
71.3 × 25.4 mm43 parts2LCERN-OHL-W-2.04OwnPod
lori28167
65 × 56.5 mm39 parts2LGPL-2.04ESP32
Smart-Universal-Remote with-Learning function and-Google-Assistant-Support
Circuit-Digest
50 × 145 mm73 parts2LNo license3STM32
Ws28xx led driver
Knifa
80 × 25 mm66 parts2LNo license3AVR/Arduino
RPM-counter
midasgossye
68.9 × 23 mm62 parts2LNo license3AVR/Arduino
Noko 2
NikolaiRadke
110 × 80 mm50 parts2LApache-2.03Nordic nRF
Keyboard
GlassyBridge
314.3 × 137 mm356 parts2LMIT2AVR/Arduino
OTTOtact
cester-ino
307 × 131.2 mm224 parts2LGPL-3.02ESP32
Aqm envcity hw
MateusMaruzka
100 × 100 mm132 parts2LNo license2AVR/Arduino
1. PDU
SshgurkiratSingh
149.5 × 113 mm106 parts4LNo license2Audio Board
woytekm
65 × 56.4 mm78 parts4LNo license2NXP
UniversalNode
DPIclimate
121.5 × 127.9 mm76 parts2LMIT2Raspberry Pi
Sensor
ReshapeTUe
64.8 × 62 mm61 parts2LNo license2Handheld Gaming device
DhairyaAPImaster
180.5 × 81.8 mm60 parts2LNo license2ESP32
TheSchaetzler
theBrutzler
56.5 × 21.5 mm56 parts2LNo license2ESP32
TUe-CBL-Circular-Electronics
bgb-0
45.3 × 40.1 mm54 parts4LCERN-OHL-P-2.02Pcb lipo power management system
devKOff
30 × 25 mm28 parts2LNo license2
How designs wire the MT3608
Read from the KiCad layouts of 168 open source designs, one per repository: what each pin of the MT3608 connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 141 of 166 designs, most often 22 µH (then 4.7 µH).
- The FB pin has a resistor to GND on 135 of 166 designs, most often 10 kΩ (then 1 kΩ).
- The IN pin has a capacitor to GND on 113 of 159 designs, most often 22 µF (then 10 µF).
- The IN pin has a inductor on 105 of 159 designs, most often 22 µH (then 4.7 µH).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SWpin 1 | Connected to: Signal 92% |
|
| GNDpin 2 | Connected to: GND 91% | — |
| FBpin 3 | Connected to: Signal 92% |
|
| ENpin 4 | Connected to: Signal 63% · 5V 31% |
|
| INpin 5 | Connected to: Signal 50% · 5V 48% |
|
| NCpin 6 | Connected to: Not connected 99% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include TERES PCB1-A64-MAIN Rev.B by OLIMEX, USBSID-Pico by LouDnl, Lesonar2 tx hardware by tornyol and Esp32s2-funprog by cnlohr.
The MT3608 in open source designs
The gallery holds 225 open source boards using the MT3608 from 180 GitHub repositories; a typical one measures about 69.8 × 65.3 mm and carries around 59 components.
82% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is TERES PCB1-A64-MAIN Rev.B by OLIMEX.
Parts used alongside the MT3608
Microcontrollers on boards using the MT3608
What boards using the MT3608 are built for
MT3608: common questions
Where can I find a MT3608 reference design?
Each of the 225 boards on this page is a real design using the MT3608. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the MT3608 SW pin connected?
The SW pin has a inductor on 141 of 166 designs, most often 22 µH (then 4.7 µH). Counted from the KiCad layouts of 168 open source designs using the MT3608.
What resistor goes on the MT3608 FB pin?
The FB pin has a resistor to GND on 135 of 166 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 168 open source designs using the MT3608.
How is the MT3608 IN pin connected?
The IN pin has a capacitor to GND on 113 of 159 designs, most often 22 µF (then 10 µF). Counted from the KiCad layouts of 168 open source designs using the MT3608.
What parts are used alongside the MT3608?
The TP4056, AMS1117-3.3, TP4056-42-ESOP8, USBLC6-2SC6 and DW01A appear in the most repositories here.
Which microcontrollers do boards using the MT3608 use?
Most are built on ESP32 (69), AVR/Arduino (24), STM32 (20) and Raspberry Pi (8).
How big is a typical board using the MT3608?
The median is 69.8 × 65.3 mm, and 82% are two-layer designs.
What is the most popular open source board using the MT3608?
By GitHub stars, TERES PCB1-A64-MAIN Rev.B by OLIMEX, with 572 stars.
Can I simulate one of these boards using the MT3608 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.