12 open source boards using the FS312F-G
Real designs built with the FS312F-G, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
OTTOtact
cester-ino
307 × 131.2 mm224 parts2LGPL-3.049ESP8266
Forcegauge
szbeni
60 × 40 mm69 parts2LGPL-3.018Raspberry Pi
Gameboy dmg
alxhoff
82.5 × 87.5 mm52 parts2LGPL-3.04AVR/Arduino
RPM-counter
midasgossye
68.9 × 23 mm62 parts2LNo license3AVR/Arduino
OTTOtact
cester-ino
307 × 131.2 mm224 parts2LGPL-3.02ESP32
ESP-32-ruler
rapha-tech
38 × 151.9 mm58 parts2LNo license0PCB BatteryCharger
sercami97
100 × 100 mm55 parts2LNo license0403 charger v2
EE403-CapStone
41.8 × 31.8 mm23 parts2LNo license0Batt
HarkonenBade
25 × 18 mm20 parts2LCC-BY-SA-4.03Bluetooth board
SirBramble
112.9 × 49.2 mm31 parts2LNo license1LiPo Charger 1
EE403-CapStone
34.9 × 27.8 mm23 parts2LNo license0AVR/Arduino
Revopod1
tongtongwang86
60 × 37 mm53 parts4LCC-BY-NC-4.05
How designs wire the FS312F-G
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the FS312F-G connects to, and the resistors, capacitors and other passives placed on it.
- The GND pin has a series capacitor on 11 of 11 designs, most often 100 nF.
- The TD pin is left unconnected on 11 of 11 designs.
- The VCC pin has a series capacitor on 9 of 11 designs, most often 100 nF.
- The CS pin has a resistor to GND on 8 of 11 designs, most often 2 kΩ (then 1 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 2 | Connected to: Signal 100% |
|
| TDpin 4 | Connected to: Not connected 100% | — |
| VCCpin 5 | Connected to: Signal 100% |
|
| GNDpin 6 | Connected to: A connector 82%, FS8205 45% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OTTOtact by cester-ino, Forcegauge by szbeni, Revopod1 by tongtongwang86 and Gameboy dmg pcb by alxhoff.
The FS312F-G in open source designs
The gallery holds 12 open source boards using the FS312F-G from 11 GitHub repositories; a typical one measures about 64.4 × 44.6 mm and carries around 54 components.
92% are two-layer designs, the rest use four layers or more, and 42% carry an open source license.
The most starred is OTTOtact by cester-ino.
Parts used alongside the FS312F-G
Microcontrollers on boards using the FS312F-G
What boards using the FS312F-G are built for
FS312F-G: common questions
Where can I find a FS312F-G reference design?
Each of the 12 boards on this page is a real design using the FS312F-G. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the FS312F-G GND pin connected?
The GND pin has a series capacitor on 11 of 11 designs, most often 100 nF. Counted from the KiCad layouts of 11 open source designs using the FS312F-G.
How is the FS312F-G TD pin connected?
The TD pin is left unconnected on 11 of 11 designs. Counted from the KiCad layouts of 11 open source designs using the FS312F-G.
How is the FS312F-G VCC pin connected?
The VCC pin has a series capacitor on 9 of 11 designs, most often 100 nF. Counted from the KiCad layouts of 11 open source designs using the FS312F-G.
What parts are used alongside the FS312F-G?
The MT3608, TP4056, FS8205, 74HC125 and ATmega32U4-AU appear in the most repositories here.
Which microcontrollers do boards using the FS312F-G use?
Most are built on AVR/Arduino (4), ESP32 (1), ESP8266 (1) and Raspberry Pi (1).
How big is a typical board using the FS312F-G?
The median is 64.4 × 44.6 mm, and 92% are two-layer designs.
What is the most popular open source board using the FS312F-G?
By GitHub stars, OTTOtact by cester-ino, with 49 stars.
Can I simulate one of these boards using the FS312F-G before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.