Rescue Line V2
About the Rescue Line V2 PCB
Rescue Line V2 is an open source ESP32 PCB design by eesakiii, published on GitHub. It is a 2-layer board measuring 61 × 57.3 mm, with 16 components from 15 distinct parts.
Its main chip is the ESP32-DEVKITC, from the ESP32 family. Other key parts include the LM1084-5.0 and DRV8833BRKT. By type, the board carries 9 connectors, 3 ICs, 2 capacitors, 1 diode and 1 resistor.
Main components on the Rescue Line V2
Rescue Line V2 bill of materials (BOM)
16 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM1084-5.0 | TO-263-3_TabPin2 | U1 |
| 1 | ESP32-DEVKITC | MODULE_ESP32-DEVKITC | U2 |
| 1 | DRV8833BRKT | DRV8833BRKT | U3 |
| 1 | Voltmeter 1 | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | COLOUR1 | PinSocket_1x03_P2.54mm_Vertical | J2 |
| 1 | COLOUR2 | PinSocket_1x03_P2.54mm_Vertical | J3 |
| 1 | USONIC1 | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | XT60-M | AMASS_XT60-M | J5 |
| 1 | EXT_DMDRIVER | PinHeader_1x06_P2.54mm_Vertical | J6 |
| 1 | MCLAW | PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | MSERVO | PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | ON/OFF Switch | PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | LED | LED_0603_1608Metric | D2 |
| 2 | 10UF20V | C_0805_2012Metric | C1, C2 |
| 1 | 150R | R_0805_2012Metric | R2 |
Rescue Line V2 design files
The KiCad project lives in the eesakiii/SilverbackPCBs repository on GitHub; these links point at the commit this page was built from.
Rescue Line V2: common questions
What microcontroller does the Rescue Line V2 use?
The Rescue Line V2 is built around the ESP32-DEVKITC, from the ESP32 family.
How big is the Rescue Line V2 PCB?
The Rescue Line V2 measures 61 × 57.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Rescue Line V2?
16 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the Rescue Line V2 design files?
From the eesakiii/SilverbackPCBs repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Rescue Line V2 design in my own project?
The repository has no license, so all rights stay with eesakiii. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Rescue Line V2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in SilverbackPCBs
Line 3.0
206 × 197.4 mm100 parts2LNo license0
AVR/ArduinoChi Chi
169 × 170 mm100 parts2LNo license0
ESP32Bulma
100 × 85 mm77 parts2LNo license0
Line 3.1
206 × 197.4 mm72 parts2LNo license0
AVR/ArduinoMain 3.1
206 × 197.4 mm65 parts2LNo license0
ESP32Line 2.3
214.9 × 206.5 mm54 parts2LNo license0
Line 2.4
214.9 × 206.5 mm53 parts2LNo license0
AVR/ArduinoMain 2.4
214.9 × 206.5 mm40 parts2LNo license0
ESP32Main 2.3
214.9 × 206.5 mm34 parts2LNo license0
ESP32Bulma2.2
85 × 118.3 mm32 parts2LNo license0
Coilgun 1.3 Main Control Board
66 × 55.9 mm10 parts2LNo license0
Earlier revisions in the repo: Rescue Line
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Esp32 minimal
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k
ESP32Controller
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k