PulseToken
ema-rauf·PulseToken·pcb/PulseToken/PulseToken.kicad_pcb
About the PulseToken PCB
PulseToken is an open source ESP32 PCB design by ema-rauf, published on GitHub. It is a 2-layer board measuring 52.4 × 37.4 mm, with 9 components from 7 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. By type, the board carries 4 connectors, 3 switches, 1 IC and 1 resistor.
It belongs with the displays & leds and power & battery designs in this gallery.
From the project
A small, battery-powered hardware 2FA token. It shows one-time login codes on an OLED screen, and only unlocks after your fingerprint is verified.
A small, battery-powered hardware 2FA token. It shows one-time login codes on an OLED screen, and only unlocks after your fingerprint is verified.
Phone authenticator apps live on a device that also gets lost, hacked, or runs out of battery. PulseToken keeps your codes on a separate pocket device that nobody else can unlock.
1. Press a button to wake PulseToken. 2. Place your finger on the sensor. The fingerprint module checks it on its own, so the fingerprint never leaves the sensor. 3. The real-time clock keeps accurate time, which the time-based codes (TOTP) need. 4. Use the three…
Main components on the PulseToken
PulseToken bill of materials (BOM)
9 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-SMD | U1 |
| 1 | RTC | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | OLED | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | FINGERPRINT | PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | BATTERY | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J4 |
| 3 | SW_Push | SW_PUSH_6mm | SW1, SW2, SW3 |
| 1 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
PulseToken design files
The KiCad project lives in the ema-rauf/PulseToken repository on GitHub; these links point at the commit this page was built from.
PulseToken: common questions
What microcontroller does the PulseToken use?
The PulseToken is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the PulseToken PCB?
The PulseToken measures 52.4 × 37.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PulseToken?
9 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the PulseToken design files?
From the ema-rauf/PulseToken repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the PulseToken design in my own project?
The repository has no license, so all rights stay with ema-rauf. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the PulseToken without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k