Twomes p1-gateway hardware
energiegedrag-nl·twomes-p1-gateway-hardware·pcb/TwomesGateway.kicad_pcb
About the Twomes p1-gateway hardware PCB
Twomes p1-gateway hardware is an open source ESP32 PCB design by energiegedrag-nl, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 35.6 × 79 mm, with 33 components from 21 distinct parts.
Its main chip is the ESP32-WROOM-32E, from the ESP32 family. Other key parts include the AP7365-33WG-7. By type, the board carries 9 resistors, 7 capacitors, 4 transistors, 4 connectors, 4 diodes and 3 switches.
It belongs with the test & measurement and iot & wireless designs in this gallery.
From the project
Open hardware design files for the Twomes P1 Gateway measurement device (Voortzetting van energietransitie/twomes-p1-gateway-hardware.)
This repository contains the open hardware design files for the Twomes P1 Gateway device, which can read measurement data from a smart meter adhering to the Dutch Smart Meter Requirements (DSMR). It can also receive data from various other Twomes 'satellite' measurement devices via the ESP-NOW protocol. The Twomes P1 Gateway can upload this measurement data to a Twomes server via Wi-Fi using secure HTTPS.

Main components on the Twomes p1-gateway hardware
Twomes p1-gateway hardware bill of materials (BOM)
33 components, 21 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP7365-33WG-7 | SOT-23-5 | U1 |
| 1 | ESP32-WROOM-32E ESP32-WROOM-32D | ESP32-WROOM-32 | U2 |
| 3 | BC807 | SOT-23 | Q1, Q2, Q3 |
| 1 | MMBT3904 | SOT-23 | Q4 |
| 1 | FTDI header | PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | RJ12-6P6C | RJ12_Amphenol_54601 | J2 |
| 1 | C404968 USB_B_Micro | ÙSB_JLC__SHOUHAN_microQTJ | J3 |
| 1 | Conn_01x06 | Rj12SMD | J4 |
| 3 | SW_Push | SW_Push_1P1T_NO_6x6mm_H9.5mm | SW1, SW2, SW3 |
| 1 | 1N4148W | D_SOD-123 | D1 |
| 1 | SS14 | D_SMA | D2 |
| 1 | C84256 LED_RED | LED_1206_3216Metric | D3 |
| 1 | C2297 LED_GREEN | LED_1206_3216Metric | D4 |
| 2 | 1UF 1uF | C_0603_1608Metric | C1, C2 |
| 3 | 100NF 100nF | C_0603_1608Metric | C3, C4, C5 |
| 1 | 1000UF 470uF | CP_Elec_8x10.5 | C6 |
| 1 | 10UF 10uF | C_0603_1608Metric | C7 |
| 3 | 1k | R_0603_1608Metric | R1, R7, R8 |
| 3 | C22936 1R | R_0603_1608Metric | R2, R3, R9 |
| 1 | 2.2K 2.2k | R_0603_1608Metric | R4 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 10K 10k | R_0603_1608Metric | R5, R6 |
Twomes p1-gateway hardware design files
The KiCad project lives in the energiegedrag-nl/twomes-p1-gateway-hardware repository on GitHub; these links point at the commit this page was built from.
Twomes p1-gateway hardware: common questions
What microcontroller does the Twomes p1-gateway hardware use?
The Twomes p1-gateway hardware is built around the ESP32-WROOM-32E, from the ESP32 family.
How big is the Twomes p1-gateway hardware PCB?
The Twomes p1-gateway hardware measures 35.6 × 79 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Twomes p1-gateway hardware?
33 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Twomes p1-gateway hardware design files?
From the energiegedrag-nl/twomes-p1-gateway-hardware repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Twomes p1-gateway hardware design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which energiegedrag-nl chose for the repository.
Can I test firmware for the Twomes p1-gateway hardware without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k