8 open source boards using the AP7365-33WG-7
Real designs built with the AP7365-33WG-7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Sea picro
joshajohnson
17.8 × 33 mm47 parts4LCERN-OHL-S-2.0195STM32
Remram
hasenbanck
140 × 104 mm259 parts4LNo license40Labio
rishabh110493
152 × 85 mm234 parts2LNo license1ESP32
Twomes p1-gateway hardware
energietransitie
35.6 × 79 mm33 parts2LCERN-OHL-P-2.01STM32
QUT Autopilot Pixracer
Heckus
44.5 × 44.5 mm140 parts4LCustom license0ESP32
Twomes p1-gateway hardware
energiegedrag-nl
35.6 × 79 mm33 parts2LCERN-OHL-P-2.00Debugger2
rishabh110493
65 × 30 mm65 parts2LNo license1STM32
QUT AutoPilot SensorTest board
Heckus
71.5 × 46 mm40 parts2LCustom license0
How designs wire the AP7365-33WG-7
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the AP7365-33WG-7 connects to, and the resistors, capacitors and other passives placed on it.
- The VOUT pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF).
- The VIN pin has a decoupling capacitor on 5 of 6 designs, most often 4.7 µF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: 5V 50% · a signal 50% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| NCpin 4 | Connected to: Not connected 100% | — |
| VOUTpin 5 | Connected to: 3.3V 100% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Sea picro by joshajohnson, Remram by hasenbanck, Twomes p1-gateway hardware by energietransitie and Debugger2 by rishabh110493.
The AP7365-33WG-7 in open source designs
The gallery holds 8 open source boards using the AP7365-33WG-7 from 6 GitHub repositories; a typical one measures about 54.7 × 62.5 mm and carries around 56 components.
63% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is Sea picro by joshajohnson.
Parts used alongside the AP7365-33WG-7
Microcontrollers on boards using the AP7365-33WG-7
What boards using the AP7365-33WG-7 are built for
AP7365-33WG-7: common questions
Where can I find a AP7365-33WG-7 reference design?
Each of the 8 boards on this page is a real design using the AP7365-33WG-7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the AP7365-33WG-7 VOUT pin?
The VOUT pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the AP7365-33WG-7.
What decoupling capacitors do designs use on the AP7365-33WG-7 VIN pin?
The VIN pin has a decoupling capacitor on 5 of 6 designs, most often 4.7 µF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the AP7365-33WG-7.
Which microcontrollers do boards using the AP7365-33WG-7 use?
Most are built on STM32 (3), ESP32 (2) and RP2040/RP2350 (1).
How big is a typical board using the AP7365-33WG-7?
The median is 54.7 × 62.5 mm, and 63% are two-layer designs.
What is the most popular open source board using the AP7365-33WG-7?
By GitHub stars, Sea picro by joshajohnson, with 195 stars.
Can I simulate one of these boards using the AP7365-33WG-7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.