ESP32-C3 True-S
EObianom·ESP32-C3_True-S
About the ESP32-C3 True-S PCB
ESP32-C3 True-S is an open source ESP32 PCB design by EObianom, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 22.3 × 25.1 mm, with 24 components from 13 distinct parts.
Its main chip is the ESP32-C3-MINI-1, from the ESP32 family. Other key parts include the ME6211C33M5. By type, the board carries 10 resistors, 5 capacitors, 3 connectors, 2 ICs, 2 switches and 2 diodes.
From the project
This is an ESP32-C3 based on the MINI-1
Main components on the ESP32-C3 True-S
ESP32-C3 True-S bill of materials (BOM)
24 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ME6211C33M5 | SOT-23-5 | U1 |
| 1 | ESP32-C3-MINI-1 | ESP32-C3-MINI-1 | U3 |
| 2 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J1, J2 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J3 |
| 2 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | SW1, SW2 |
| 2 | LED | LED_0603_1608Metric | D2, D3 |
| 2 | 0.1uF | C_0402_1005Metric | C13, C16 |
| 1 | 10uF | C_0402_1005Metric | C14 |
| 2 | 1uF | C_0402_1005Metric | C19, C20 |
| 4 | 10K | R_0402_1005Metric | R4, R5, R6, R7 |
| 2 | 5.1K | R_0402_1005Metric | R8, R9 |
| 2 | 22 | R_0402_1005Metric | R10, R11 |
| 2 | 220 | R_0402_1005Metric | R12, R13 |
ESP32-C3 True-S design files
The KiCad project lives in the EObianom/ESP32-C3_True-S repository on GitHub; these links point at the commit this page was built from.
- LayoutESP32-C3_True-S.kicad_pcb
- SchematicESP32-C3_True-S.kicad_sch
ESP32-C3 True-S: common questions
What microcontroller does the ESP32-C3 True-S use?
The ESP32-C3 True-S is built around the ESP32-C3-MINI-1, from the ESP32 family.
How big is the ESP32-C3 True-S PCB?
The ESP32-C3 True-S measures 22.3 × 25.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32-C3 True-S?
24 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the ESP32-C3 True-S design files?
From the EObianom/ESP32-C3_True-S repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the ESP32-C3 True-S design in my own project?
It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.
Can I test firmware for the ESP32-C3 True-S without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k