Shapdesk esphome
evgkg·shapdesk-esphome·hardware/pcb/shapdesk_rev2.kicad_pcb
About the Shapdesk esphome PCB
Shapdesk esphome is an open source ESP32 PCB design by evgkg, published on GitHub under the MIT license. It is a 2-layer board measuring 91.2 × 18 mm, with 28 components from 9 distinct parts.
Its main chip is the ESP32-C3 SuperMini, from the ESP32 family. Other key parts include the ME6211C33M5G-N. By type, the board carries 16 resistors, 7 transistors, 2 ICs, 2 capacitors and 1 connector.
It belongs with the iot & wireless designs in this gallery.
From the project
ESPHome firmware for Shapdesk standing desks: Wi-Fi control, height monitoring, and Home Assistant integration on ESP32-C3.
A small add-on that connects a Shapdesk standing desk to Home Assistant over Wi-Fi. An ESP32-C3 SuperMini board lives in a little 3D-printed box on the back of the original handset. It presses the handset's buttons for you and reads the desk height from the data the handset sends over UART. In Home Assistant the desk shows up through ESPHome: raise and lower it, send it to a height, recall presets 1–4 and press M.

Main components on the Shapdesk esphome
Shapdesk esphome bill of materials (BOM)
28 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3 SuperMini | ESP32-C3_SuperMini_2x08 | U1 |
| 1 | ME6211C33M5G-N | SOT-23-5 | U2 |
| 7 | MMBT3904 | SOT-23_Handsoldering | Q1, Q2, Q3, Q4, Q5, Q6, Q7 |
| 1 | Conn_02x05 | PinHeader_2x05_P2.54mm_Horizontal | J1 |
| 2 | 10uF | C_0805_2012Metric | C1, C2 |
| 7 | 100k | R_0603_1608Metric | R1, R2, R3, R4, R5, R6, R7 |
| 7 | 4.7k | R_0603_1608Metric | R8, R9, R10, R11, R12, R13, R14 |
| 1 | 10k | R_0603_1608Metric | R15 |
| 1 | 18k | R_0603_1608Metric | R16 |
Shapdesk esphome design files
The KiCad project lives in the evgkg/shapdesk-esphome repository on GitHub; these links point at the commit this page was built from.
Shapdesk esphome: common questions
What microcontroller does the Shapdesk esphome use?
The Shapdesk esphome is built around the ESP32-C3 SuperMini, from the ESP32 family.
How big is the Shapdesk esphome PCB?
The Shapdesk esphome measures 91.2 × 18 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Shapdesk esphome?
28 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Shapdesk esphome design files?
From the evgkg/shapdesk-esphome repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Shapdesk esphome design in my own project?
Yes, under the terms of its MIT license, which evgkg chose for the repository.
Can I test firmware for the Shapdesk esphome without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k