45 open source boards using the ESP32-C3_SUPERMINI

Real designs built with the ESP32-C3_SUPERMINI, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

45 boardsClear filters|Most starred

How designs wire the ESP32-C3_SUPERMINI

Read from the KiCad layouts of 32 open source designs, one per repository: what each pin of the ESP32-C3_SUPERMINI connects to, and the resistors, capacitors and other passives placed on it.

  • The 3V3 pins is tied to 3.3V on 60% of them (not connected on 7, a signal on 5).
3V3pin 3.3, 14Connected to: 3.3V 60% · not connected 23% · a signal 17%
GPIO8_12pin 12Connected to: A connector 25% · not connected 40%
  • Series resistor on 30% · 2.2 kΩ (2), 4.7 kΩ (2), 10 kΩ (1)
GPIO9_13pin 13Connected to: Signal 55% · not connected 45%
  • Series resistor on 30% · 330 Ω (2), 4.7 kΩ (2), 20 Ω (1)
GNDpin 15, GConnected to: GND 67% · not connected 17% · a signal 17%

15 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include TheTick by jkramarz, Rust esp32c3-examples by ChocolateLoverRaj, Baby tracker suite by aamat09 and BlueJamma by KPEKEP.

The ESP32-C3_SUPERMINI in open source designs

The gallery holds 45 open source boards using the ESP32-C3_SUPERMINI from 36 GitHub repositories; a typical one measures about 65 × 60.9 mm and carries around 29 components.

93% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.

The most starred is TheTick by jkramarz.

Parts used alongside the ESP32-C3_SUPERMINI

Microcontrollers on boards using the ESP32-C3_SUPERMINI

ESP32-C3_SUPERMINI: common questions

Where can I find a ESP32-C3_SUPERMINI reference design?

Each of the 45 boards on this page is a real design using the ESP32-C3_SUPERMINI. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ESP32-C3_SUPERMINI 3V3 pin connected?

The 3V3 pins is tied to 3.3V on 60% of them (not connected on 7, a signal on 5). Counted from the KiCad layouts of 32 open source designs using the ESP32-C3_SUPERMINI.

What parts are used alongside the ESP32-C3_SUPERMINI?

The TP4056, AMS1117-3.3, L7805 and SN65HVD230 appear in the most repositories here.

Which microcontrollers do boards using the ESP32-C3_SUPERMINI use?

Most are built on ESP32 (45).

How big is a typical board using the ESP32-C3_SUPERMINI?

The median is 65 × 60.9 mm, and 93% are two-layer designs.

What is the most popular open source board using the ESP32-C3_SUPERMINI?

By GitHub stars, TheTick by jkramarz, with 183 stars.

Can I simulate one of these boards using the ESP32-C3_SUPERMINI before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part