Receiver
EwoudVV·clicker·receiver/receiver.kicad_pcb
About the Receiver PCB
Receiver is an open source ESP32 PCB design by EwoudVV, published on GitHub. It is a 2-layer board measuring 20.8 × 34.1 mm, with 10 components from 9 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N4, from the ESP32 family. Other key parts include the AP2112K-3.3TRG1. By type, the board carries 3 capacitors, 2 ICs, 1 connector and 1 diode.
It belongs with the keyboards and iot & wireless designs in this gallery.
From the project
wireless 2 switch macropad
This project is 2 pcbs. One is a reciever, which you plug into your computer, and the other is a remote, or transmitter, with the buttons. The reciever acts like a keyboard, so no drivers need to be installed on the computer.
Reciever pcb: - 2 layer - esp32 s3 - has a usb-c port for computer - an led that blinks when something is being sent
Remote pcb: - same esp32 s3 - small battery - 2 switches (khalih choc v1 smd) - 2 layer - 2 side assembly - usb-c port for charging
Main components on the Receiver
Receiver bill of materials (BOM)
10 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N4 ESP32-S3-WROOM-1 Espressif | ESP32-S3-WROOM-1 | U1 |
| 1 | AP2112K-3.3TRG1 AP2112K-3.3 Diodes Inc | SOT-23-5 | U2 |
| 1 | TYPE-C-31-M-12 USB-C HRO | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | DEBUG Generic | PinHeader_1x03_P2.54mm_Vertical | HDR1 |
| 2 | 5.1k | R_0603_1608Metric | R_CC1, R_CC2 |
| 1 | 19-213/R6C-AL1M2VY/3T ACT Everlight | LED_0603_1608Metric | D1 |
| 1 | CL10B104KB8NNNC 100nF Samsung | C_0603_1608Metric | C1 |
| 1 | CL10A106MQ8NNNC 10uF Samsung | C_0603_1608Metric | C2 |
| 1 | CL10B105KO8NNNC 1uF Samsung | C_0603_1608Metric | C3 |
Receiver design files
The KiCad project lives in the EwoudVV/clicker repository on GitHub; these links point at the commit this page was built from.
Receiver: common questions
What microcontroller does the Receiver use?
The Receiver is built around the ESP32-S3-WROOM-1-N4, from the ESP32 family.
How big is the Receiver PCB?
The Receiver measures 20.8 × 34.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Receiver?
10 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Receiver design files?
From the EwoudVV/clicker repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Receiver design in my own project?
The repository has no license, so all rights stay with EwoudVV. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Receiver without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in clicker
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k