21 open source boards using the ESP32-S3-WROOM-1-N4

Real designs built with the ESP32-S3-WROOM-1-N4, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

21 boardsClear filters|Most starred

How designs wire the ESP32-S3-WROOM-1-N4

Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the ESP32-S3-WROOM-1-N4 connects to, and the resistors, capacitors and other passives placed on it.

  • The EN pin has a pull-up to 3.3V on 14 of 16 designs, most often 10 kΩ (then 100 kΩ).
  • The EN pin has a capacitor to GND on 13 of 16 designs, most often 1 µF (then 100 nF).
  • The IO45 pin is left unconnected on 15 of 16 designs.
  • The 3V3 pin is tied to 3.3V on 14 of 16 designs (a signal on 2).
GNDpin 1, 40, 41Connected to: GND 100%
3V3pin 2Connected to: 3.3V 88%
ENpin 3Connected to: Signal 100%
  • Pull-up to 3.3V on 88% · 10 kΩ (13), 100 kΩ (1)
  • Capacitor to GND on 81% · 1 µF (8), 100 nF (8)
IO8pin 12Connected to: A connector 38% · not connected 19%
  • Pull-up to 3.3V on 38% · 4.7 kΩ (2), 10 kΩ (1), 100 kΩ (1)
IO3pin 15Connected to: Not connected 73% · a signal 27%
IO46pin 16Connected to: Not connected 81%
IO9pin 17Connected to: Signal 81% · not connected 19%
  • Pull-up to 3.3V on 38% · 4.7 kΩ (3), 10 kΩ (1), 100 kΩ (1)
IO48pin 25Connected to: Not connected 63% · a signal 38%
IO45pin 26Connected to: Not connected 94%
IO0pin 27Connected to: Signal 100%
  • Capacitor to GND on 50% · 100 nF (7), 4.7 nF (1)
  • Pull-up to 3.3V on 44% · 10 kΩ (7)
IO35pin 28Connected to: Not connected 75% · a signal 25%
IO36pin 29Connected to: Not connected 75% · a signal 25%
IO37pin 30Connected to: Not connected 69% · a signal 31%
IO38pin 31Connected to: Signal 56% · not connected 44%
  • Series resistor on 31% · 1 kΩ (2), 2.2 kΩ (1), 100 Ω (1)
IO39pin 32Connected to: Not connected 63% · a signal 38%
IO40pin 33Connected to: Not connected 69% · a signal 31%
IO41pin 34Connected to: Not connected 69% · a signal 31%
IO42pin 35Connected to: Not connected 63% · a signal 38%
IO2pin 38Connected to: Not connected 63% · a signal 38%

20 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ups to esp32 by aronreid, Monolith by luftaquila, Fugu2 by fl4p and Spikeling by OpenSourceNeuro.

The ESP32-S3-WROOM-1-N4 in open source designs

The gallery holds 21 open source boards using the ESP32-S3-WROOM-1-N4 from 18 GitHub repositories; a typical one measures about 62.5 × 69.7 mm and carries around 48 components.

62% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.

The most starred is Ups to esp32 by aronreid.

Parts used alongside the ESP32-S3-WROOM-1-N4

Microcontrollers on boards using the ESP32-S3-WROOM-1-N4

ESP32-S3-WROOM-1-N4: common questions

Where can I find a ESP32-S3-WROOM-1-N4 reference design?

Each of the 21 boards on this page is a real design using the ESP32-S3-WROOM-1-N4. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the ESP32-S3-WROOM-1-N4 EN pin?

The EN pin has a pull-up to 3.3V on 14 of 16 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 16 open source designs using the ESP32-S3-WROOM-1-N4.

How is the ESP32-S3-WROOM-1-N4 IO45 pin connected?

The IO45 pin is left unconnected on 15 of 16 designs. Counted from the KiCad layouts of 16 open source designs using the ESP32-S3-WROOM-1-N4.

How is the ESP32-S3-WROOM-1-N4 3V3 pin connected?

The 3V3 pin is tied to 3.3V on 14 of 16 designs (a signal on 2). Counted from the KiCad layouts of 16 open source designs using the ESP32-S3-WROOM-1-N4.

What parts are used alongside the ESP32-S3-WROOM-1-N4?

The AMS1117-3.3, AP63203WU-7, TP4056 and USBLC6-2SC6 appear in the most repositories here.

Which microcontrollers do boards using the ESP32-S3-WROOM-1-N4 use?

Most are built on ESP32 (21).

How big is a typical board using the ESP32-S3-WROOM-1-N4?

The median is 62.5 × 69.7 mm, and 62% are two-layer designs.

What is the most popular open source board using the ESP32-S3-WROOM-1-N4?

By GitHub stars, Ups to esp32 by aronreid, with 63 stars.

Can I simulate one of these boards using the ESP32-S3-WROOM-1-N4 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part