Tablet sensor board
explora26·tablet_sensor_board
About the Tablet sensor board
Tablet sensor board is an open source PCB design by explora26, published on GitHub. It is a board, with 11 components from 9 distinct parts.
Other key parts include the TLV75530PDBV and LIS3DH. By type, the board carries 4 capacitors, 3 resistors, 2 ICs and 2 connectors.
It belongs with the sensors designs in this gallery.
From the project
板上用 LDO 轉出 3.0V,讓 I2C 電位和 NanoPC-T4 的 I2C2(3.0V I/O)一致,同時經 JST 接頭供電和 I2C 給 BQ25798 充電板。
板上用 LDO 轉出 3.0V,讓 I2C 電位和 NanoPC-T4 的 I2C2(3.0V I/O)一致,同時經 JST 接頭供電和 I2C 給 BQ25798 充電板。
I2C2 上的位址:LIS3DH 是 0x18,BQ25798 是 0x6B,沒有衝突。
建議: - C3、C4 靠近 LIS3DH 的 VDD(pin 14) - LIS3DH 放在螺絲孔附近、遠離接頭,減少拔插時的應力 - B.Cu 整面 GND - 線寬 0.25 mm、間距 0.13 mm、過孔 0.6/0.3 mm,在 JLCPCB 標準製程範圍內
Main components on the Tablet sensor board
Tablet sensor board bill of materials (BOM)
11 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TLV75530PDBV | SOT-23-5 | U1 |
| 1 | LIS3DH | LGA-16_3x3mm_P0.5mm_LayoutBorder3x5y | U2 |
| 1 | T4_I2C2 | PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | BQ25798_BOARD | JST_PH_B5B-PH-K_1x05_P2.00mm_Vertical | J2 |
| 2 | 1uF | C_0603_1608Metric | C1, C2 |
| 1 | 100nF | C_0603_1608Metric | C3 |
| 1 | 10uF | C_0603_1608Metric | C4 |
| 2 | 4.7k | R_0603_1608Metric | R1, R2 |
| 1 | 10k | R_0603_1608Metric | R3 |
Tablet sensor board design files
The KiCad project lives in the explora26/tablet_sensor_board repository on GitHub; these links point at the commit this page was built from.
- Schematiclis3dh_board.kicad_sch
- BOMfab/bom.csv
Tablet sensor board: common questions
How many components are on the Tablet sensor board?
11 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Tablet sensor board design files?
From the explora26/tablet_sensor_board repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the Tablet sensor board design in my own project?
The repository has no license, so all rights stay with explora26. Use it as a reference, and ask the author before reusing the design.
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2kSensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kPots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956