Boost converter
fabianmink·MarbleAccelerator·electronics/boost_converter/boost_converter.kicad_pcb
About the Boost converter PCB
Boost converter is an open source PCB design by fabianmink, published on GitHub under the BSD-2-Clause license. It is a 2-layer board measuring 75 × 40 mm, with 26 components from 13 distinct parts.
Other key parts include the MC34063AP. By type, the board carries 12 resistors, 6 capacitors, 3 connectors, 1 IC, 1 fuse and 1 diode.
It belongs with the power & battery designs in this gallery.
From the project
An accelerator / coilgun for metallic marbles
Coil winding cross sections are 15mm (coil length) x 7mm (inner radius 8mm, outer radius 15mm), leading to around 350 turns for 0.5mm wire diameter which results in an inductance of approximately 1mH.
Horizontal CAD design (base and tube parts)
The design is intended to be used with EVERLIGHT ITR9904 optical sensor for marble detection.
Vertical CAD design (base part and output)

Main components on the Boost converter
Boost converter bill of materials (BOM)
26 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MC34063AP | DIP-8_W7.62mm | U1 |
| 2 | Screw_Terminal_01x02 | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J1, J3 |
| 1 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | Polyfuse | Fuse_BelFuse_0ZRE0005FF_L8.3mm_W3.8mm | F1 |
| 1 | Thermistor_PTC | RV_Disc_D9mm_W3.3mm_P5mm | TH1 |
| 1 | 1N5819 | D_DO-41_SOD81_P10.16mm_Horizontal | D1 |
| 1 | L | L_Radial_D10.0mm_P5.00mm_Fastron_07P | L1 |
| 1 | C_Polarized | CP_Radial_D10.0mm_P2.50mm_P5.00mm | C1 |
| 1 | C | C_Disc_D3.0mm_W2.0mm_P2.50mm | C2 |
| 2 | C | C_Rect_L4.6mm_W3.8mm_P2.50mm_MKS02_FKP02 | C3, C6 |
| 1 | C | C_Rect_L4.6mm_W4.6mm_P2.50mm_MKS02_FKP02 | C4 |
| 1 | C_Polarized | CP_Radial_D10.0mm_P5.00mm_P7.50mm | C5 |
| 12 | R | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R3, R4, R5, R6, R7, R8 +4 |
Boost converter design files
The KiCad project lives in the fabianmink/MarbleAccelerator repository on GitHub; these links point at the commit this page was built from.
Boost converter: common questions
How big is the Boost converter PCB?
The Boost converter measures 75 × 40 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Boost converter?
26 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Boost converter design files?
From the fabianmink/MarbleAccelerator repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Boost converter design in my own project?
Yes, under the terms of its BSD-2-Clause license, which fabianmink chose for the repository.
More boards in MarbleAccelerator
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1k