Meshbee hardware
fablab-imperia·meshbee-hardware·pcb/Meshbee_transmitter.kicad_pro/Meshbee_001.kicad_pro.kicad_pcb
About the Meshbee hardware PCB
Meshbee hardware is an open source ESP32 PCB design by fablab-imperia, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 42.5 × 164 mm, with 23 components from 22 distinct parts.
Its main chip is the ESP32, from the ESP32 family. Other key parts include the Wemos_LoLin32_lite, HT-RA62, CD74HC4067M 16 channel multiplexer and nice_nano. By type, the board carries 11 connectors, 4 ICs, 4 resistors, 2 switches and 2 capacitors.
From the project
Questo progetto è distribuito sotto licenza CERN-OHL-S
Questo progetto è distribuito sotto licenza CERN-OHL-S
Sviluppato per apicoltori e monitoraggio ambientale.
Main components on the Meshbee hardware
Meshbee hardware bill of materials (BOM)
23 components, 22 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Wemos_LoLin32_lite | Lolin_32_Lite_Board_1 | U1 |
| 1 | HT-RA62 | HT-RA62 | U2 |
| 1 | CD74HC4067M 16 channel multiplexer | CD74HC4067M 16 channel multiplexer | U3 |
| 1 | nice_nano | nice_nano | U4 |
| 1 | sensor 0 | MeshBee_JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J1 |
| 1 | sensor 1 | MeshBee_JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J2 |
| 1 | sensor 2 | MeshBee_JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J3 |
| 1 | sensor 3 | MeshBee_JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J4 |
| 1 | sensor 4 | MeshBee_JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J5 |
| 1 | sensor 5 | MeshBee_JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J6 |
| 1 | sensor 6 | MeshBee_JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J7 |
| 1 | sensor 7 | MeshBee_JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J8 |
| 1 | Reset/AP_Button | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J9 |
| 1 | Battery | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J10 |
| 1 | ESP32 | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J11 |
| 1 | button | button | SW1 |
| 1 | reset | button | SW2 |
| 1 | 100nF | CP_Radial_Tantal_D5.0mm_P2.50mm | C1 |
| 1 | 47µF | CP_Radial_D5.0mm_P2.00mm | C2 |
| 2 | 10k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R2 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1M | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3 |
| 1 | 750k | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R4 |
Meshbee hardware design files
The KiCad project lives in the fablab-imperia/meshbee-hardware repository on GitHub; these links point at the commit this page was built from.
Meshbee hardware: common questions
What microcontroller does the Meshbee hardware use?
The Meshbee hardware is built around the ESP32, from the ESP32 family.
How big is the Meshbee hardware PCB?
The Meshbee hardware measures 42.5 × 164 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Meshbee hardware?
23 components, from 22 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Meshbee hardware design files?
From the fablab-imperia/meshbee-hardware repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Meshbee hardware design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which fablab-imperia chose for the repository.
Can I test firmware for the Meshbee hardware without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k