ESP32-adapter pan woom
About the ESP32-adapter pan woom PCB
ESP32-adapter pan woom is an open source ESP32 PCB design by fabriziotappero, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 97.4 × 95.9 mm, with 26 components from 17 distinct parts.
Its main chip is the ESP-WROOM-32, from the ESP32 family. Other key parts include the XC6220B281MR-G, INA226_SOT25-5 and SI7060-00. By type, the board carries 6 connectors, 4 ICs, 4 switches, 4 capacitors, 4 resistors and 2 transistors.
From the project
a lot of embedded programming material for the Espressif ESP32
Main components on the ESP32-adapter pan woom
ESP32-adapter pan woom bill of materials (BOM)
26 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XC6220B281MR-G AP1117 | SOT-223 | U1 |
| 1 | ESP-WROOM-32 ES-WROOM-32 | ESP-WROOM-32-short | U2 |
| 1 | INA226_SOT25-5 ESP3212 | ESP3212-short | U3 |
| 1 | SI7060-00 AP1117 | SOT-223 | U4 |
| 2 | AO3401 | sot23 | Q1, Q2 |
| 2 | CONN_01X19 | Pin_Header_Straight_1x19 | P1, P3 |
| 2 | CONN_01X02 | mkds_1,5-2 | P2, P5 |
| 2 | CONN_01X16 | Pin_Header_Straight_1x16 | P4, P6 |
| 4 | SW_PUSH | smd_push | SW1, SW2, SW3, SW4 |
| 1 | MMSZ5V6CF 10V | MELF_Standard | D1 |
| 1 | ESDZL5-1F4 10V | MELF_Standard | D2 |
| 1 | 100nF | c_1206 | C1 |
| 1 | 10U 100nF | c_1206 | C2 |
| 2 | 100N 100nF | c_1206 | C3, C4 |
| 1 | 10K R | r_0603 | R1 |
| 2 | 100R 100k | r_0603 | R2, R4 |
| 1 | 100R R | r_0603 | R3 |
ESP32-adapter pan woom design files
The KiCad project lives in the fabriziotappero/esp32-embed repository on GitHub; these links point at the commit this page was built from.
ESP32-adapter pan woom: common questions
What microcontroller does the ESP32-adapter pan woom use?
The ESP32-adapter pan woom is built around the ESP-WROOM-32, from the ESP32 family.
How big is the ESP32-adapter pan woom PCB?
The ESP32-adapter pan woom measures 97.4 × 95.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32-adapter pan woom?
26 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ESP32-adapter pan woom design files?
From the fabriziotappero/esp32-embed repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the ESP32-adapter pan woom design in my own project?
Yes, under the terms of its GPL-3.0 license, which fabriziotappero chose for the repository.
Can I test firmware for the ESP32-adapter pan woom without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in esp32-embed
ESP32ESP32-li ion cell monitor pan
94 × 26 mm47 parts2LGPL-3.00
ESP32ESP32-li ion cell monitor
90 × 26 mm45 parts2LGPL-3.00
ESP32ESP32-bat monitor latch
33 × 50 mm29 parts2LGPL-3.00
ESP32ESP32-bat monitor latch pan
66 × 100 mm29 parts2LGPL-3.00
ESP32ESP32-adapter pan
97.4 × 96.6 mm26 parts2LGPL-3.00
ESP32ESP32-adapter
68 × 55.4 mm26 parts2LGPL-3.00
ESP32-epaper adapter
23 × 29 mm20 parts2LGPL-3.00
ESP32-epaper adapter pan
23 × 29 mm20 parts2LGPL-3.00
ESP32ESP32-adapter pan esp3212
97 × 94.7 mm13 parts2LGPL-3.00
ESP32ESP32-wroover adapter pan
37 × 81 mm6 parts2LGPL-3.00
ESP32ESP32-wroover adapter
27 × 37 mm6 parts2LGPL-3.00
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Esp32 minimal
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k
ESP32Controller
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k