HardLabs

ESP32-bat monitor latch

fabriziotappero·esp32-embed·kicad-boards/ESP32-bat-monitor-latch/ESP32-bat-monitor-latch.kicad_pcb

ESP32-bat monitor latch PCB layout, top view — open source ESP32 board by fabriziotappero

About the ESP32-bat monitor latch PCB

ESP32-bat monitor latch is an open source ESP32 PCB design by fabriziotappero, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 33 × 50 mm, with 29 components from 18 distinct parts.

Its main chip is the ESP-WROOM-32, from the ESP32 family. Other key parts include the XC6220B281MR-G. By type, the board carries 10 connectors, 6 resistors, 5 transistors, 5 capacitors and 2 ICs.

It belongs with the power & battery designs in this gallery.

From the project

a lot of embedded programming material for the Espressif ESP32

ESP32-bat monitor latch, from the project README
From the project README

Main components on the ESP32-bat monitor latch

XC6220B281MR-GESP-WROOM-32

ESP32-bat monitor latch bill of materials (BOM)

29 components, 18 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
XC6220B281MR-G
MAX809
U1
1
ESP-WROOM-32
ES-WROOM-32
U2
2
2N7002
Q1, Q3
3
AO3401
Q2, Q4, Q5
2
CONN_01X01_FEMALE
CONN_01X02
J1, J2
1
CONN_01X05_MALE
CONN_01X02
J3
2
CONN_01X02
J4, J5
4
TEST_1P
J6, J7, J8, J9
1
CONN_01X05
J10
1
VAL**
hole_3mm
1
100nF
C1
2
10U
100nF
C2, C5
1
100N
100nF
C3
1
100N
10uF
C4
1
10K
2M2
R1
2
100R
2M2
R2, R4
2
100R
100k
R3, R6
1
100MR
100k
R5

ESP32-bat monitor latch design files

The KiCad project lives in the fabriziotappero/esp32-embed repository on GitHub; these links point at the commit this page was built from.

ESP32-bat monitor latch: common questions

What microcontroller does the ESP32-bat monitor latch use?

The ESP32-bat monitor latch is built around the ESP-WROOM-32, from the ESP32 family.

How big is the ESP32-bat monitor latch PCB?

The ESP32-bat monitor latch measures 33 × 50 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the ESP32-bat monitor latch?

29 components, from 18 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the ESP32-bat monitor latch design files?

From the fabriziotappero/esp32-embed repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the ESP32-bat monitor latch design in my own project?

Yes, under the terms of its GPL-3.0 license, which fabriziotappero chose for the repository.

Can I test firmware for the ESP32-bat monitor latch without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in esp32-embed

Similar boards