Display
Felix-Jr056·TECHIN514A-Wi26·FinalProject/KiCAD/Display/Display.kicad_pcb
About the Display PCB
Display is an open source ESP32 PCB design by Felix-Jr056, published on GitHub. It is a 2-layer board measuring 114.6 × 58.3 mm, with 8 components from 6 distinct parts.
Its main chip is the LM317MBSTT3G, from the ESP32 family. By type, the board carries 3 diodes, 2 connectors, 1 IC, 1 module and 1 switch.
It belongs with the displays & leds, iot & wireless and power & battery designs in this gallery.
From the project
Components used in the sensor device include: - Pressure Sensors: 3 FSRs (Force Sensitive Resistor). - Microcontroller: Custom PCB, may include FSR resistor network, status LED. - Wireless Module: For transmitting data to the display device (BLE). - Battery: Rechargeable LiPo bat
Components used in the sensor device include: - Pressure Sensors: 3 FSRs (Force Sensitive Resistor). - Microcontroller: Custom PCB, may include FSR resistor network, status LED. - Wireless Module: For transmitting data to the display device (BLE). - Battery: Rechargeable LiPo battery with battery indicator.
Components used in the display device include: - 1 Microcontroller: ESP32. - 1 Stepper motor driven gauge needle: To visually represent the user's posture. - 3 LEDs: Indicate the pressure level at each sensor. - 1 Button: For calibration and session reset functionality. - 1 Battery: Small…

Main components on the Display
Display bill of materials (BOM)
8 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM317MBSTT3G XIAO ESP32C3 | NEWxiao_esp32c3 | U1 |
| 1 | Stepper_Motor_bipolar | x27_stepper | M1 |
| 1 | CONN_01X04_PIN Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | Battery | PinSocket_1x02_P2.54mm_Vertical | J5 |
| 1 | SW_SPDT | PinHeader_1x03_P2.54mm_Vertical | SW1 |
| 3 | 1655 | LED_1655 | D1, D2, D3 |
Display design files
The KiCad project lives in the Felix-Jr056/TECHIN514A-Wi26 repository on GitHub; these links point at the commit this page was built from.
Display: common questions
What microcontroller does the Display use?
The Display is built around the LM317MBSTT3G, from the ESP32 family.
How big is the Display PCB?
The Display measures 114.6 × 58.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Display?
8 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Display design files?
From the Felix-Jr056/TECHIN514A-Wi26 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Display design in my own project?
The repository has no license, so all rights stay with Felix-Jr056. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Display without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in TECHIN514A-Wi26
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k