LupaProject
fenglingling0·lupaProject·lupa_github/v2_razemy_jst/proekt_kicad/lupa_plata.kicad_pcb
About the LupaProject PCB
LupaProject is an open source ESP32 PCB design by fenglingling0, published on GitHub. It is a 4-layer board measuring 28.1 × 67 mm, with 75 components from 45 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the BQ21061YFPR, TPS63802DLAR, TMUX1101DCKR, QMI8658B and ME6211C28M5G-N. By type, the board carries 28 resistors, 24 capacitors, 8 ICs, 5 connectors, 4 switches and 3 diodes.
It belongs with the audio, power & battery and iot & wireless designs in this gallery.
From the project
Handheld camera magnifier. ESP32-S3-WROOM-1-N16R8, OV5640 (DVP, 24-pin FPC), 4-layer, 28.2 x 67.1 mm, KiCad 9. Two-sided SMT assembly at JLCPCB.
Handheld camera magnifier. ESP32-S3-WROOM-1-N16R8, OV5640 (DVP, 24-pin FPC), 4-layer, 28.2 x 67.1 mm, KiCad 9. Two-sided SMT assembly at JLCPCB.
- Power: USB-C -> BQ21061 (charger / power path) -> TPS63802 buck-boost -> 3V3. Hard on/off via SPDT on the TPS63802 EN. Camera rails: ME6211 (2V8), TLV75515 (1V5). - Audio: PDM mic (MSM261) direct to GPIO, MAX98357A I2S amp. Storage: microSD over SPI. IMU: QMI8658B (INT on an RTC GPIO, wake-up). - Battery sense: 100k/100k divider gated by TMUX1101 (IO18 enable, IO16 sense). - Programming and logging over native USB (IO19/IO20); UART0 pins are used…
Main components on the LupaProject
LupaProject bill of materials (BOM)
75 components, 45 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N16R8 | ESP32-S3-WROOM-1 | U1 |
| 1 | BQ21061YFPR | Texas_YFP0020_DSBGA-20_tight | U2 |
| 1 | TPS63802DLAR | TPS63802_VSON-HR-10_2x3mm | U3 |
| 1 | TMUX1101DCKR | SOT-353_SC-70-5 | U4 |
| 1 | QMI8658B | LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y | U5 |
| 1 | ME6211C28M5G-N | SOT-23-5 | U6 |
| 1 | TLV75515PDBV | SOT-23-5 | U7 |
| 1 | MAX98357A | TQFN-16-1EP_3x3mm_P0.5mm_EP1.23x1.23mm | U8 |
| 1 | C5143397 USB-C | USB_C_Receptacle_GCT_USB4110 | X1 |
| 1 | C131337 LiPo 1S | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J1 |
| 1 | C202112 OV5640 DVP FPC24 | Hirose_FH12-24S-0.5SH_1x24-1MP_P0.50mm_Horizontal | J2 |
| 1 | C131337 Speaker 8R 1-2W | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J3 |
| 1 | C5912397 microSD SPI | microSD_HC_Wuerth_693072010801 | J4 |
| 1 | C131337 External trigger | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J5 |
| 1 | MSM261DDB019 | MSM261DDB019 | MK1 |
| 1 | C231329 RESET | SW_SPST_B3U-1000P | SW1 |
| 1 | C231329 BOOT | SW_SPST_B3U-1000P | SW2 |
| 1 | C231329 TRIGGER | SW_SPST_B3U-1000P | SW3 |
| 1 | JS102011SAQN MAIN ON/OFF | SW_SPDT_PCM12 | SW4 |
| 1 | C2286 USB_PRESENT | LED_0603_1608Metric | D1 |
Show 25 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C2286 TALK_L | LED_0603_1608Metric | D2 |
| 1 | C2286 TALK_R | LED_0603_1608Metric | D3 |
| 1 | TFM201610GHM-R47MTAA 0.47uH | L_Changjiang_FTC201610S | L1 |
| 2 | 10UF 10uF | C_0402_1005Metric | C1, C6 |
| 2 | 2.2UF 2.2uF | C_0402_1005Metric | C2, C5 |
| 1 | 4.7UF 4.7uF | C_0402_1005Metric | C3 |
| 2 | 100NF 100nF | C_0402_1005Metric | C4, C24 |
| 1 | 22UF 22uF | C_1206_3216Metric | C7 |
| 5 | 100NF 100nF | C_0603_1608Metric | C8, C9, C11, C17, C19 |
| 4 | 10UF 10uF | C_0805_2012Metric | C10, C18, C20, C21 |
| 5 | 1UF 1uF | C_0603_1608Metric | C12, C13, C14, C15, C16 |
| 1 | 1UF 1uF | C_0402_1005Metric | C22 |
| 1 | 22UF 22uF | C_0603_1608Metric | C23 |
| 2 | 5.1K 5.1k | R_0603_1608Metric | R1, R2 |
| 1 | 10K 10k | R_0402_1005Metric | R3 |
| 9 | 10K 10k | R_0603_1608Metric | R4, R12, R13, R18, R19, R20, R21, R22 +1 |
| 1 | 100K 100k | R_0402_1005Metric | R5 |
| 1 | C4147 91k 1% | R_0402_1005Metric | R6 |
| 1 | C64042 511k 1% | R_0402_1005Metric | R7 |
| 2 | C335088 100k 0.1% | R_0603_1608Metric | R8, R9 |
| 4 | 4.7K 4.7k | R_0603_1608Metric | R10, R11, R14, R15 |
| 4 | 1k | R_0603_1608Metric | R16, R24, R25, R26 |
| 1 | 5.6K 5.6k | R_0603_1608Metric | R17 |
| 1 | 100K 100k | R_0603_1608Metric | R27 |
| 1 | 1M | R_0603_1608Metric | R28 |
LupaProject design files
The KiCad project lives in the fenglingling0/lupaProject repository on GitHub; these links point at the commit this page was built from.
LupaProject: common questions
What microcontroller does the LupaProject use?
The LupaProject is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.
How big is the LupaProject PCB?
The LupaProject measures 28.1 × 67 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the LupaProject?
75 components, from 45 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the LupaProject design files?
From the fenglingling0/lupaProject repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the LupaProject design in my own project?
The repository has no license, so all rights stay with fenglingling0. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the LupaProject without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k