TapeLED
About the TapeLED PCB
TapeLED is an open source ESP32 PCB design by fujiy, published on GitHub. It is a 2-layer board measuring 20 × 75 mm, with 29 components from 21 distinct parts.
Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. Other key parts include the LM2842X. By type, the board carries 13 resistors, 3 ICs, 3 transistors, 3 capacitors, 2 connectors and 2 diodes.
Main components on the TapeLED
TapeLED bill of materials (BOM)
29 components, 21 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U1 |
| 1 | LM2842X | TSOT-23-6 | U2 |
| 1 | ~ | SOT-23-6 | U3 |
| 3 | Q_NMOS_GSD | TSOT-23 | Q1, Q2, Q3 |
| 1 | PINHD_1x4_Female | PinSocket_1x04_P2.54mm_Vertical | J1 |
| 1 | Barrel_Jack_Switch | BarrelJack_Kycon_KLDX-0202-xC_Horizontal | J2 |
| 1 | SW_Push | SW_PUSH_6mm | SW1 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_Receptacle_XKB_U262-16XN-4BVC11 | USB1 |
| 1 | 1A | D_SOD-123 | D1 |
| 1 | LED | LED_0603_1608Metric | D2 |
| 1 | 10uH 1.1A | L_1210_3225Metric | L1 |
| 1 | 10uF | C_0603_1608Metric | C1 |
| 1 | 10µF | C_0603_1608Metric | C2 |
| 1 | 1uF | C_0603_1608Metric | C4 |
| 2 | 5.1k | R_0603_1608Metric | R1, R2 |
| 1 | 10k | R_0603_1608Metric | R3 |
| 1 | 15k | R_0603_1608Metric | R4 |
| 4 | 1k | R_0603_1608Metric | R5, R11, R12, R13 |
| 1 | 20k | R_0603_1608Metric | R6 |
| 3 | 100k | R_0603_1608Metric | R7, R9, R10 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 4.7k | R_0603_1608Metric | R8 |
TapeLED design files
The KiCad project lives in the fujiy/Home repository on GitHub; these links point at the commit this page was built from.
- LayoutTapeLED/TapeLED.kicad_pcb
- SchematicTapeLED/TapeLED.kicad_sch
TapeLED: common questions
What microcontroller does the TapeLED use?
The TapeLED is built around the ESP32-C3-WROOM-02, from the ESP32 family.
How big is the TapeLED PCB?
The TapeLED measures 20 × 75 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the TapeLED?
29 components, from 21 distinct parts. The full bill of materials is listed on this page.
Where can I download the TapeLED design files?
From the fujiy/Home repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the TapeLED design in my own project?
The repository has no license, so all rights stay with fujiy. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the TapeLED without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Home
ESP32Stencil
44 × 40 mm54 parts2LNo license0
ESP32Driver
45 × 40 mm46 parts2LNo license0
ESP32ColorCorrecter
20 × 77 mm35 parts2LNo license0
ESP32TableLamp
29.5 × 38 mm27 parts2LNo license0
ESP32LightConsole
33 × 55 mm26 parts2LNo license0
ESP32RemoteHub
33 × 55 mm26 parts2LNo license0
ESP32LightBar
16 × 65 mm26 parts2LNo license0
LEDboardLarge
100 × 100 mm22 parts2LNo license0
ESP32Curtains
30 × 50 mm19 parts2LNo license0
LEDboard
46 × 46 mm14 parts2LNo license0
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Esp32 minimal
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k
ESP32Controller
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k