166 open source boards using the ESP32-C3-WROOM-02

Real designs built with the ESP32-C3-WROOM-02, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

166 boardsClear filters|Most starred

How designs wire the ESP32-C3-WROOM-02

Read from the KiCad layouts of 125 open source designs, one per repository: what each pin of the ESP32-C3-WROOM-02 connects to, and the resistors, capacitors and other passives placed on it.

  • The 3V3 pin is tied to 3.3V on 111 of 125 designs (not connected on 2, a signal on 11).
  • The EN pin has a pull-up to 3.3V on 92 of 125 designs, most often 10 kΩ (then 100 kΩ).
  • The EN pin has a capacitor to GND on 88 of 125 designs, most often 1 µF (then 100 nF).
  • The IO8 pin has a pull-up to 3.3V on 63 of 125 designs, most often 10 kΩ (then 4.7 kΩ).
3V3pin 1Connected to: 3.3V 89%
ENpin 2Connected to: Signal 94%
  • Pull-up to 3.3V on 74% · 10 kΩ (82), 100 kΩ (2), 5.1 kΩ (2)
  • Capacitor to GND on 70% · 1 µF (49), 100 nF (36), 10 µF (3)
IO8pin 7Connected to: A connector 21% · not connected 18%
  • Pull-up to 3.3V on 50% · 10 kΩ (47), 4.7 kΩ (7), 100 kΩ (3)
IO9pin 8Connected to: A connector 26%
  • Pull-up to 3.3V on 47% · 10 kΩ (47), 4.7 kΩ (4), 5.1 kΩ (2)
GNDpin 9, 19Connected to: GND 93%
IO2pin 16Connected to: Signal 73% · not connected 27%
  • Pull-up to 3.3V on 39% · 10 kΩ (39), 100 kΩ (4), 2.2 kΩ (1)

12 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Picframe colepd by Spritetm, Air quality sensor by roepkefeller, FunHomeLight by ZhiFun and SommerESP by exico91.

The ESP32-C3-WROOM-02 in open source designs

The gallery holds 166 open source boards using the ESP32-C3-WROOM-02 from 133 GitHub repositories; a typical one measures about 51.4 × 50.6 mm and carries around 38 components.

78% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.

The most starred is Picframe colepd by Spritetm.

Microcontrollers on boards using the ESP32-C3-WROOM-02

ESP32-C3-WROOM-02: common questions

Where can I find a ESP32-C3-WROOM-02 reference design?

Each of the 166 boards on this page is a real design using the ESP32-C3-WROOM-02. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the ESP32-C3-WROOM-02 3V3 pin connected?

The 3V3 pin is tied to 3.3V on 111 of 125 designs (not connected on 2, a signal on 11). Counted from the KiCad layouts of 125 open source designs using the ESP32-C3-WROOM-02.

What pull-up resistor is used on the ESP32-C3-WROOM-02 EN pin?

The EN pin has a pull-up to 3.3V on 92 of 125 designs, most often 10 kΩ (then 100 kΩ). Counted from the KiCad layouts of 125 open source designs using the ESP32-C3-WROOM-02.

What pull-up resistor is used on the ESP32-C3-WROOM-02 IO8 pin?

The IO8 pin has a pull-up to 3.3V on 63 of 125 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 125 open source designs using the ESP32-C3-WROOM-02.

What parts are used alongside the ESP32-C3-WROOM-02?

The AP2112K-3.3, USBLC6-2SC6, AMS1117-3.3, MCP73831-2-OT and CH224K appear in the most repositories here.

Which microcontrollers do boards using the ESP32-C3-WROOM-02 use?

Most are built on ESP32 (162), RP2040/RP2350 (3) and STM32 (1).

How big is a typical board using the ESP32-C3-WROOM-02?

The median is 51.4 × 50.6 mm, and 78% are two-layer designs.

What is the most popular open source board using the ESP32-C3-WROOM-02?

By GitHub stars, Picframe colepd by Spritetm, with 96 stars.

Can I simulate one of these boards using the ESP32-C3-WROOM-02 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part