Cat feeder
fxp·cat-feeder·round-1/hardware/v2-jlc-bom/cat_feeder.kicad_pcb
About the Cat feeder PCB
Cat feeder is an open source ESP32 PCB design by fxp, published on GitHub. It is a 2-layer board measuring 66 × 60 mm, with 32 components from 24 distinct parts.
Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. Other key parts include the AMS1117-3.3. By type, the board carries 9 resistors, 6 capacitors, 4 connectors, 3 switches, 3 diodes and 2 ICs.
From the project
AI-agent-designed automatic cat feeder (ESP32-C3 + HX711 + motor): schematic, PCB (Gerber/BOM), firmware, enclosure, docs
第一块板:ESP32-C3-WROOM-02 + AMS1117-3.3 + AO3400A 低边电机驱动 + HX711 接口 + UART/BOOT/RESET/FEED 按键。 28 个元件、18 个网络,66×60 mm 双层,DRC 0 错误 / 0 未连接(17 张网络布通)。
三份用的是同一份规格(元件和网络完全相同),Gerber 因为是各自重新生成的,字节不同。
reports/REPORT.md:2026-10-19 12:46 → 13:15(墙钟 1749 秒,9 个 Agent 回合),三个 Agent(circuit / structure / firmware)同时开工, 最多 3 个同时活跃;ZCode CLI 0.17.0(由 zai-org/ZCode main 构建),模型 glm-5.3(经 BigModel)。
Main components on the Cat feeder
Cat feeder bill of materials (BOM)
32 components, 24 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | AO3400A | SOT-23 | Q1 |
| 1 | 5V IN | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | UART GND TX RX | PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | MOTOR | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | HX711 3V3 GND DT SCK | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 4 | MountingHole_2.2mm | H1, H2, H3, H4 | |
| 1 | C231329 RESET | SW_SPST_B3U-1000P | SW1 |
| 1 | C231329 BOOT | SW_SPST_B3U-1000P | SW2 |
| 1 | C231329 FEED | SW_SPST_B3U-1000P | SW3 |
| 1 | 1N5819WS | D_SOD-323 | D1 |
| 1 | C12624 green | LED_0603_1608Metric | D2 |
| 1 | C2286 red | LED_0603_1608Metric | D3 |
| 2 | 22UF 22uF | C_0805_2012Metric | C1, C2 |
| 1 | 10UF 10uF | C_0805_2012Metric | C3 |
| 1 | 100NF 100nF | C_0603_1608Metric | C4 |
| 1 | 1UF 1uF | C_0603_1608Metric | C5 |
| 1 | 100UF 100uF | CP_Elec_6.3x5.4 | C6 |
| 5 | 10K 10k | R_0603_1608Metric | R1, R2, R3, R4, R7 |
Show 4 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 100R | R_0603_1608Metric | R5 |
| 1 | 100K 100k | R_0603_1608Metric | R6 |
| 1 | 330R | R_0603_1608Metric | R8 |
| 1 | 1k | R_0603_1608Metric | R9 |
Cat feeder design files
The KiCad project lives in the fxp/cat-feeder repository on GitHub; these links point at the commit this page was built from.
Cat feeder: common questions
What microcontroller does the Cat feeder use?
The Cat feeder is built around the ESP32-C3-WROOM-02, from the ESP32 family.
How big is the Cat feeder PCB?
The Cat feeder measures 66 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Cat feeder?
32 components, from 24 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Cat feeder design files?
From the fxp/cat-feeder repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Cat feeder design in my own project?
The repository has no license, so all rights stay with fxp. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Cat feeder without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in cat-feeder
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k