Cat feeder rev b

fxp·cat-feeder·round-2/hardware/cat_feeder_rev_b.kicad_pcb

Cat feeder rev b PCB layout, top view — open source ESP32 board by fxp

About the Cat feeder rev b PCB

Cat feeder rev b is an open source ESP32 PCB design by fxp, published on GitHub. It is a 2-layer board measuring 66 × 60 mm, with 35 components from 26 distinct parts.

Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. Other key parts include the AMS1117-3.3 and INA199A2. By type, the board carries 10 resistors, 7 capacitors, 4 connectors, 3 ICs, 3 switches and 3 diodes.

From the project

AI-agent-designed automatic cat feeder (ESP32-C3 + HX711 + motor): schematic, PCB (Gerber/BOM), firmware, enclosure, docs

在 Rev A 上加了电机电流检测,并把线缆集中到一侧。32 个元件、21 个网络,板子尺寸和安装孔不变, DRC 0 错误 / 0 未连接(20/20 张网络布通)。

订单包里没核实的事项:所有元件都没有嘉立创料号(LCSC);坐标文件的旋转偏移没核对;D1、D2、D3、C6 和 U3 的极性要在嘉立创预览里人工看; R10 的封装是 4 脚开尔文型(RShuntOhmiteLVK12`),普通 2 脚 2512 贴不上;从没烧录、上电或实际组装过。

第二轮里 firmware / enclosure 的改动、运行报告和时间线,在私有引擎仓库 fxp/zcode-magic 的 zcode-team/runs/round-2/ 里。 所以 ../round-1/firmware 和 ../round-1/enclosure 仍是第一轮(Rev A)的版本,没有 I_SENSE 电流检测。

Main components on the Cat feeder rev b

Cat feeder rev b bill of materials (BOM)

35 components, 26 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-C3-WROOM-02
U1
1
AMS1117-3.3
U2
1
INA199A2
U3
1
AO3400A
Q1
1
5V IN
J1
1
UART GND TX RX
J2
1
MOTOR
J3
1
HX711 3V3 GND DT SCK
J4
4
MountingHole_2.2mm
H1, H2, H3, H4
1
RESET
SW1
1
BOOT
SW2
1
FEED
SW3
1
1N5819WS
D1
1
green
D2
1
red
D3
2
22UF
22uF
C1, C2
1
10UF
10uF
C3
2
100NF
100nF
C4, C7
1
1UF
1uF
C5
1
100UF
100uF
C6
Show 6 more
QtyPartRefs
5
10K
10k
R1, R2, R3, R4, R7
1
100R
R5
1
100K
100k
R6
1
330R
R8
1
1k
R9
1
20MR
20mR
R10

Cat feeder rev b design files

The KiCad project lives in the fxp/cat-feeder repository on GitHub; these links point at the commit this page was built from.

Cat feeder rev b: common questions

What microcontroller does the Cat feeder rev b use?

The Cat feeder rev b is built around the ESP32-C3-WROOM-02, from the ESP32 family.

How big is the Cat feeder rev b PCB?

The Cat feeder rev b measures 66 × 60 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Cat feeder rev b?

35 components, from 26 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Cat feeder rev b design files?

From the fxp/cat-feeder repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Cat feeder rev b design in my own project?

The repository has no license, so all rights stay with fxp. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Cat feeder rev b without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in cat-feeder

Similar boards