Home fan
GitBMP·home-fan

About the Home fan PCB
Home fan is an open source PCB design by GitBMP, published on GitHub under the CERN-OHL-P-2.0 license. It is a board, with 63 components from 18 distinct parts.
Other key parts include the DS18B20. By type, the board carries 20 capacitors, 18 resistors, 10 diodes, 8 connectors, 4 switches and 1 IC.
It belongs with the sensors designs in this gallery.
From the project
ESP32-C6 controller for two reversing room fans. Replaces the electronics of an inVENTer iV14 decentralised ventilation system with 12 V PWM fans. KiCad, JLCPCB assembly, Rust firmware.
Open hardware controller for two reversing 12 V PWM fans, built around an ESP32-C6.
Replaces the electronics of an inVENTer® iV14 decentralised ventilation system: the wall sleeve, ducting and covers stay, the original fans and the 24 V controller are replaced by two ebm-papst 4412FGMPR fans and this board. It fits the older square 120 × 120 mm fan sleeves, not the newer round iV14R / iV14V units. It is not electrically compatible with the original controller (e.g. sMove) or fans: inVENTer uses voltage control, this board uses 3-wire PWM fans.
Main components on the Home fan
Home fan bill of materials (BOM)
63 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DS18B20 HXY MOSFET | TO-92_Inline | U4 |
| 1 | BC847BS hongjiacheng | SOT-363_SC-70-6 | Q1 |
| 2 | KF301-5.0-3P KEFA(科发) | CONN-TH_3P-P5.00_KF301-5.0-3P | J3, J4 |
| 2 | M2510V-04P-N3 XFCN(兴飞) | CONN-TH_4P-P2.54_XFCN_M2510V-04P-N3 | J5, J6 |
| 2 | B4B-XH-A(LF)(SN) JST-XH 4P JST | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J7, J8 |
| 1 | S4B-XH-A(LF)(SN) JST-XH 4P JST | JST_XH_S4B-XH-A_1x04_P2.50mm_Horizontal | J9 |
| 1 | B3B-PH-K-S(LF)(SN) JST-PH 3P JST | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J10 |
| 1 | PTA3043-2010CIB103 BOURNS | RES-ADJ-TH_PTA3043 | RV1 |
| 4 | K2-6639SP-I4SC-04 韩国韩荣 | KEY-SMD_4P-L6.0-W6.0-P3.90-LS10.0 | SW3, SW4, SW5, SW6 |
| 10 | WS2812B-2020 worldsemi | LED-SMD_4P-L2.0-W2.0-TL_WS2812B-2020 | D5, D6, D7, D8, D9, D10, D11, D12 +2 |
| 20 | CC0603KRX7R9BB104 100nF YAGEO | C_0603_1608Metric | C14, C15, C16, C17, C18, C19, C20, C21 +12 |
| 2 | 0603WAF1001T5E 1k UNI-ROYAL(Uniroyal Elec) | R_0603_1608Metric | R7, R12 |
| 8 | 0603WAF1002T5E 10k UNI-ROYAL(Uniroyal Elec) | R_0603_1608Metric | R8, R9, R13, R14, R17, R18, R19, R20 |
| 2 | 0603WAF0000T5E 0R UNI-ROYAL(Uniroyal Elec) | R_0603_1608Metric | R10, R11 |
| 1 | 0603WAF3301T5E 3k3 UNI-ROYAL(Uniroyal Elec) | R_0603_1608Metric | R15 |
| 1 | 0603WAF1000T5E 100R UNI-ROYAL(Uniroyal Elec) | R_0603_1608Metric | R16 |
| 1 | 0603WAF3300T5E 330R UNI-ROYAL(Uniroyal Elec) | R_0603_1608Metric | R21 |
| 3 | 0603WAF4701T5E 4k7 UNI-ROYAL(Uniroyal Elec) | R_0603_1608Metric | R22, R23, R24 |
Home fan design files
The KiCad project lives in the GitBMP/home-fan repository on GitHub; these links point at the commit this page was built from.
- SchematicESP32-C6-2.kicad_sch
Home fan: common questions
How many components are on the Home fan?
63 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the Home fan design files?
From the GitBMP/home-fan repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Home fan design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which GitBMP chose for the repository.
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2kSensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kPots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956