118 open source boards using the DS18B20
Real designs built with the DS18B20, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
HB-LC-Dim6PWM-CV
stan23
139 × 56.3 mm57 parts2LCC-BY-NC-4.021AVR/Arduino
Matrixclock gnm-19881-bsg
WiseLord
191.8 × 48.4 mm35 parts2LNo license16AVR/Arduino
Zuendbox v3 32
fixxl
213.6 × 127.5 mm153 parts2LNo license10STM32
CMM2-JLC
Manawyrm
130 × 102 mm110 parts2LGPL-3.010AVR/Arduino
Tiny85fancontrol
Colahall
25.4 × 25.4 mm11 parts2LMIT10ESP32
Meteo station
alicjamusial
110 × 90 mm23 parts2LCC-BY-SA-4.08ESP32
Final H00 panelicad
Vedatori
240 × 174.3 mm86 parts2LNo license7AVR/Arduino
TeCoLab
ytcsc
95.1 × 93.8 mm48 parts2LMIT7AVR/Arduino
AVRThermostat
protaskin
54.6 × 71.8 mm31 parts2LMIT7AVR/Arduino
Bertha main
Hackuarium
100 × 87 mm155 parts2LNo license6Klipper-Fan-Hat
mikepthomas
65 × 56.5 mm59 parts2LGPL-3.06Espled
Yottabits
100 × 50 mm41 parts2LNo license6STM32
Hm stm32 2ch dimmer
der-pw
56 × 55.4 mm33 parts2LNo license6Raspberry Pi
Pcb smarter pi
klein0r
56 × 65 mm20 parts2LMIT6STM32
ActiveLoad
ahessling
50 × 100 mm75 parts2LMIT5ESP32
SensactHs
klaus-liebler
100 × 86.5 mm317 parts2LApache-2.04STM32
BigSur
ParadigmHyperloop
196.4 × 70 mm145 parts2LCustom license4ESP32
PaLampa MoBo H00
Vedatori
60 × 100 mm75 parts2LNo license4AVR/Arduino
RaspberryPi UPS HAT
gvoigtlaender
65 × 56 mm52 parts2LGPL-3.04OBeMS
johnbeardmore
180 × 120 mm123 parts2LLGPL-3.03ESP32
NixieNTPClock
bastian-bou
181.4 × 77.2 mm58 parts4LGPL-3.03Spotwelderix
swifty99
100 × 70 mm58 parts2LGPL-3.02AVR/Arduino
Weather station
z0b1
37.3 × 36.5 mm11 parts4LNo license2NXP
Teensy boardV 1
Cosys-Lab
66.5 × 46 mm590 parts2LCC-BY-SA-4.01PIC
PIC DEV BOARD
anshukumar146
140.7 × 128.5 mm102 parts4LNo license1AVR/Arduino
Remote-Antenna-Switch
EI9SP
193.6 × 95 mm82 parts2LNo license1ESP32
Espac
metehus
95 × 95 mm62 parts2LNo license1ESP32
BirdNest
VorosEgyes
100 × 100 mm42 parts2LMIT1Hardware
gfroerli
56 × 90 mm37 parts2LNo license1AVR/Arduino
Gas sensor
Hackuarium
100 × 100 mm32 parts2LNo license1- schematic only · 36 partsAVR/Arduino
Smart-Viscosity-Measurement and-Control-System-VYTRON
rashadrahimzade
36 partsCustom license1 - schematic only · 28 partsESP32
Hydroponic veggie garden
Gregovate
28 partsMIT1 - schematic only · 8 partsESP32
Routeur solaire
aginies
8 parts2LNo license1 AVR/Arduino
Campervan management V2.1
akladnig
169.5 × 96 mm168 parts4LNo license0AVR/Arduino
NotePad
Meteopresscz
151 × 212 mm155 parts2LNo license0STM32
Hvac v2
candykingdom
125 × 93 mm154 parts2LNo license0
How designs wire the DS18B20
Read from the KiCad layouts of 77 open source designs, one per repository: what each pin of the DS18B20 connects to, and the resistors, capacitors and other passives placed on it.
- The DQ pin has a pull-up to 3.3V on 54 of 76 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 81% | — |
| DQpin 2 | Connected to: The microcontroller 58%, a connector 21% |
|
| VDDpin 3 | Connected to: 3.3V 77% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OT Thing Tester by Phunkafizer, Esp32-temp by angelnu, HB-LC-Dim5PWM-CV AskSinDuino32Shield by stan23 and Matrixclock gnm-19881-bsg by WiseLord.
The DS18B20 in open source designs
The gallery holds 118 open source boards using the DS18B20 from 85 GitHub repositories; a typical one measures about 90 × 73 mm and carries around 58 components.
91% are two-layer designs, the rest use four layers or more, and 42% carry an open source license.
The most starred is OT Thing Tester by Phunkafizer.
Parts used alongside the DS18B20
Microcontrollers on boards using the DS18B20
What boards using the DS18B20 are built for
DS18B20: common questions
Where can I find a DS18B20 reference design?
Each of the 118 boards on this page is a real design using the DS18B20. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the DS18B20 DQ pin?
The DQ pin has a pull-up to 3.3V on 54 of 76 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 77 open source designs using the DS18B20.
What parts are used alongside the DS18B20?
The AMS1117-3.3, ATMEGA328P-AU, ESP32-S3-WROOM-1, Arduino_Nano_v3.x and BME280 appear in the most repositories here.
Which microcontrollers do boards using the DS18B20 use?
Most are built on ESP32 (39), AVR/Arduino (32), STM32 (8) and ESP8266 (7).
How big is a typical board using the DS18B20?
The median is 90 × 73 mm, and 91% are two-layer designs.
What is the most popular open source board using the DS18B20?
By GitHub stars, OT Thing Tester by Phunkafizer, with 25 stars.
Can I simulate one of these boards using the DS18B20 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.