CHOTU

Gurjas2112·CHOTU·hardware/pcb/chotu_carrier.net

CHOTU

About the CHOTU PCB

CHOTU is an open source ESP32 PCB design by Gurjas2112, published on GitHub under the MIT license. It is a board, with 54 components from 39 distinct parts.

Its main chip is the ESP32-S3-DevKitC-1 (N8R8), from the ESP32 family. Other key parts include the XL4015 5V/5A buck module and TB6612FNG module. By type, the board carries 20 resistors, 18 connectors, 4 test points, 4 capacitors, 3 ICs and 2 transistors.

It belongs with the power & battery, robotics & motion and dev boards & breakouts designs in this gallery.

From the project

Smart Room Cleaning Autonomous Robot

A 2-layer, 90 × 65 mm carrier board for the ESP32-S3-DevKitC-1. It replaces the breadboard and jumper wiring of the AtomQuest build (oldessentialdocs/Botcircuitdiagram.jpg, botconnectionschema.jpeg). Every GPIO matches the firmware's firmware/esp32s3basecontroller/include/pins.h, and tests/testpcbnetlist.py fails if they ever differ.**

Trace widths. 2.0 mm for the battery, motor and vacuum nets (the vacuum peaks at about 5 A), 1.0 mm for +5V, 0.3 mm for signals. Star ground. Motor and vacuum returns join logic ground at one point next to the XT60. Pour GND on the bottom layer. No copper…

Main components on the CHOTU

CHOTU bill of materials (BOM)

54 components, 39 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-DevKitC-1 (N8R8)
U1
1
XL4015 5V/5A buck module
U2
1
TB6612FNG module
U3
2
IRLZ44N
Q1, Q2
1
XT60 battery 3S 11.1V
J1
1
Rocker switch (panel)
J2
1
Raspberry Pi 4 5V feed (GPIO pins 2/6)
J3
1
Left BO motor
J4
1
Right BO motor
J5
1
Encoder L (LM393)
J6
1
Encoder R (LM393)
J7
1
HC-SR04 L
J8
1
HC-SR04 C
J9
1
HC-SR04 R
J10
1
VL53L0X ToF
J11
1
MPU6050 IMU
J12
1
SW-420 bump
J13
1
TCRT5000 cliff L
J14
1
TCRT5000 cliff R
J15
1
TSOP38238 dock IR
J16
Show 19 more
QtyPartRefs
1
Bergmann BAV-60 vacuum 12V/60W
J17
1
Side-brush motor 12V
J18
1
Fuse 10A ATO
F1
1
TP VBAT
TP1
1
TP +5V
TP2
1
TP +3V3
TP3
1
TP GND
TP4
2
1N5822
D1, D2
1
470uF 25V
C1
1
1000uF 10V
C2
1
4.7UF
4.7uF
C3
1
100NF
100nF
C4
3
10K
10k
R1, R16, R18
5
1k
R2, R4, R6, R8, R10
5
2k
R3, R5, R7, R9, R11
2
4.7K
4.7k
R12, R13
3
100R
R14, R15, R17
1
100K
100k
R19
1
22K
22k
R20

CHOTU design files

The KiCad project lives in the Gurjas2112/CHOTU repository on GitHub; these links point at the commit this page was built from.

CHOTU: common questions

What microcontroller does the CHOTU use?

The CHOTU is built around the ESP32-S3-DevKitC-1 (N8R8), from the ESP32 family.

How many components are on the CHOTU?

54 components, from 39 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the CHOTU design files?

From the Gurjas2112/CHOTU repository on GitHub, which has a netlist and the BOM; the links under Design files point to each one.

Can I use the CHOTU design in my own project?

Yes, under the terms of its MIT license, which Gurjas2112 chose for the repository.

Can I test firmware for the CHOTU without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards